Datasheet

VCA810
www.ti.com SBOS275F –JUNE 2003–REVISED DECEMBER 2010
ELECTRICAL CHARACTERISTICS: V
S
= ±5V
Boldface limits are tested at +25°C.
At R
L
= 500Ω, and V
IN
= single-ended input on V+ with V− at ground,, unless otherwise noted.
VCA810
MIN/MAX OVER
TYP TEMPERATURE
0°C to –40°C to MIN/ TEST
PARAMETER CONDITIONS +25°C +25°C
(2)
+70°C
(3)
+85°C
(3)
UNITS MAX LEVEL
(1)
AC PERFORMANCE
Small-signal bandwidth (see Figure 29) −2V ≤ V
C
≤ 0V 35 30 29 29 MHz min B
Large-signal bandwidth V
O
= 2V
PP
, −2 ≤ V
C
≤ −1 35 30 29 29 MHz min B
Frequency response peaking V
O
< 500mV
PP
, −2V ≤ V
C
≤ 0V 0.1 0.5 0.5 0.5 dB min B
Slew rate V
O
= 3.5V Step, −2 ≤ V
C
≤ −1, 10% to 90% 350 300 300 295 V/ms min B
Settling time to 0.01% V
O
= 1V Step, −2 ≤ V
C
≤ −1 30 40 41 41 ns min B
Rise-and-fall time V
O
= 1V Step, −2 ≤ V
C
≤ −1 10 12 12.1 12.1 ns min B
Group delay G = 0dB, V
C
=−1V, f = 5MHz, V
O
= 500mV
PP
6.2 ns typ C
Group delay variation V
O
< 500mV
PP
, −2V ≤ V
C
≤ 0V, f = 5MHz 3.5 ns typ C
Harmonic distortion
Second harmonic V
O
= 1V
PP
, f = 1MHz, V
C
= −1V, G = 0dB –71 –51 –50 –49 dBc min B
Third harmonic V
O
= 1V
PP
, f = 1MHz, V
C
= −1V, G = 0dB −35 –34 –32 –29 dBc min B
Input voltage noise V
C
= −2V 2.4 2.8 3.4 3.5 nV/√Hz max B
Input current noise −2V ≤ V
C
≤ 0V 1.4 1.8 2.0 2.1 pA/√Hz max B
Fully attenuated feedthrough f ≤ 1MHz, V
C
> +200mV −80 −70 dB max B
Overdrive recovery V
IN
= 2V to 0V, V
C
= −2V, G = 40dB 100 150 ns min B
DC PERFORMANCE Single-ended or differential input
Output offset voltage (both inputs
−2V ≤ V
C
≤ 0V ±4 ±22 ±30 ±32 mV max A
grounded)
(4)
Output offset voltage drift ±125 ±125 V/°C max B
Input offset voltage
(4)
Both inputs grounded ±0.1 ±0.25 ±0.30 ±0.35 mV max A
input offset voltage drift ±1 ±1.2 mV/°C max B
Input bias current −2V ≤ V
C
≤ 0V −6 –10 −12 −14 mA max A
Input bias current drift ±25 ±30 nA/°C max B
Input offset current −2V ≤ V
C
≤ 0V ±100 ±600 ±700 ±800 nA max A
Input offset current drift ±1.4 ±2.2 nA/°C max B
INPUT
Common-mode input range ±2.4 ±2.3 ±2.3 ±2.2 V min A
Common-mode rejection ratio V
CM
= 0.5V, V
C
= −2V, Input-referred 95 85 83 80 dB min A
Input impedance V
CM
= 0V, Single-ended 1|| 1 MΩ || pF typ C
V
CM
= 0V, Differential > 10 || < 2 MΩ || pF typ C
Differential input range
(5)
V
C
= 0V, V
CM
= 0V 3 V
PP
typ C
OUTPUT
Voltage output swing V
C
= −2V, R
L
= 100Ω ±1.8 ±1.7 ±1.4 ±1.3 V min A
V
C
= −2V, R
L
= 100Ω ±1.7 ±1.6 ±1.3 ±1.2 V min A
Output current V
O
= 0V ±60 ±40 ±35 ±32 mA min A
Output short-circuit current V
O
= 0V ±120 mA typ C
Output impedance V
O
= 0V, f < 100kHz 0.2 Ω typ C
(1) Test levels: (A) 100% tested at +25°C. Over temperature limits set by characterization and simulation. (B) Limits set by characterization
and simulation. (C) Typical value; only for information.
(2) Junction temperature = ambient for +25°C tested specifications.
(3) Junction temperature = ambient at low temperature limit; junction temperature = ambient +30°C at high temperature limit for over
temperature specifications.
(4) Total output offset is: (Output Offset Voltage ± Input Offset Voltage x Gain).
(5) Maximum input at minimum gain for < 1dB gain compression.
Copyright © 2003–2010, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): VCA810