Datasheet
SGLS245D − MAY 2004 − REVISED APRIL 2008
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ordering information
UCC2813-
QD
Package
D = Plastic SOIC, PW = Plastic TSSOP
Product Option
0 through 5
Automotive Temperature Range Indicator
R
Tape and Reel Indicator
0
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
†‡
V
CC
voltage
w
12 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V
CC
current
w
30 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, I
O
±1 A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output energy (capacitive load) 20 µJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog inputs (FB, CS) −0.3 V to 6.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power dissipation at T
A
< +25_C (D package) 0.65 W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
−65_C to 150_C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds 300_C. . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡
Unless otherwise indicated, voltages are reference to ground and currents are positive into and negative out of the specified terminals.
w In normal operation V
CC
is powered through a current limiting resistor. Absolute maximum of 12 V applies when V
CC
is driven from a low
impedance source such that I
CC
does not exceed 30 mA (which includes gate drive current requirement).
electrical characteristics T
A
= −40_C to 125_C, V
CC
= 10 V (see Note 1), RT = 100 kΩ from REF to
RC, CT = 330 pF from RC to GND, 0.1-F capacitor from V
CC
to GND, 0.1-F capacitor from V
REF
to
GND, and T
A
= T
J
(unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Reference Section
Output voltage
T
J
= 25_C, I = 0.2 mA
UCC2813-0/-1/-2/-4 4.925 5 5.075
V
Output voltage
T
J
= 25_C, I = 0.2 mA
UCC2813-3/-5 3.94 4 4.06
V
Load regulation voltage I = 0.2 mA to 5 mA 10 30 mV
Total variation voltage
See Note 5
UCC2813-0/-1/-2/-4 4.84 5 5.1
V
Total variation voltage See Note 5
UCC2813-3/-5 3.84 4 4.08
V
Output noise voltage
f = 10 Hz to 10 kHz,
See Note 7
T
J
= 25_C 70 µV
Long term stability
1000 hours,
See Note 7
T
A
= 125_C 5 mV
Output short-circuit current −5 −35 mA