Datasheet
TVP5154A
www.ti.com
SLES214C–DECEMBER 2007–REVISED SEPTEMBER 2010
2.3 Terminal Functions
TERMINAL
I/O DESCRIPTION
NAME NO.
Analog Section
Analog inputs for Channel 1. Connect to the video analog input via a 0.1-µF capacitor. The
AIP1A 2 maximum input range is 0–0.75 V
PP
, and may require an attenuator to reduce the input
I
AIP1B 3 amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the
schematic in Section 10.
Analog inputs for Channel 2. Connect to the video analog input via a 0.1-µF capacitor. The
AIP2A 11 maximum input range is 0-0.75 V
PP
, and may require an attenuator to reduce the input
I
AIP2B 12 amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the
schematic in Section 10.
Analog inputs for Channel 3. Connect to the video analog input via a 0.1-µF capacitor. The
AIP3A 22 maximum input range is 0-0.75 V
PP
, and may require an attenuator to reduce the input
I
AIP3B 23 amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the
schematic in Section 10.
Analog inputs for Channel 4. Connect to the video analog input via a 0.1-µF capacitor. The
AIP4A 31 maximum input range is 0-0.75 V
PP
, and may require an attenuator to reduce the input
I
AIP4B 32 amplitude to the desired level. If not used, connect to AGND via a 0.1-µF capacitor. See the
schematic in Section 10.
8, 15, 19,
AVDD P Analog power supply. Connect to 1.8-V analog supply.
28, 127
9, 16, 20,
AGND 29, 35, G Analog power supply return. Connect to analog ground.
128
1, 10, 21,
AIxGND G Analog input signal return. Connect to analog ground.
30
5, 14, 25,
PLL_GND G PLL power supply return. Connect to analog ground.
34
4, 13, 24,
PLL_VDD P PLL power supply. Connect to 1.8-V analog supply.
33
6, 17, 26, Reference supply decoupling . Connect to analog ground through a 1-µF capacitor. Connect
REFMx I
125 to REFPx through a 1-µF capacitor.
7, 18, 27, Reference supply decoupling . Connect to analog ground through a 1-µF capacitor. Connect
REFPx I
126 to REFMx through a 1-µF capacitor.
Digital Section
47, 66, 82,
DGND G Digital power supply return. Connect to digital ground
99, 116
46, 65, 81,
DVDD P Digital power supply. Connect to 1.8-V digital supply.
98, 115
44, 63, 79,
IOGND G I/O power supply return. Connect to digital ground.
96, 113
45, 64, 80,
IOVDD P I/O power supply. Connect to 3.3-V digital supply
97, 114
1. FID: Odd/even field indicator or vertical lock indicator. For the odd/even indicator, a 1
FID1/GLCO1 94
indicates the odd field.
FID2/GLCO2 75
O 2. GLCO: This serial output carries color PLL information. A slave device can decode the
FID3/GLCO3 56
information to allow chroma frequency control from the TVP5154A decoder. Data is
FID4/GLCO4 37
transmitted at the CLK rate in Genlock mode.
AVID1 101
AVID2 78 Active video indicator. This signal is high during the horizontal active time of the video
O
AVID3 59 output.
AVID4 40
1. Interrupt request : Open drain when active low.
INTREQ1/GPCL1/VBLK1 102
2. GPCL: General-purpose output. In this mode, the state of GPCL is directly programmed
INTREQ2/GPCL2/VBLK2 83
via I
2
C.
I/O
INTREQ3/GPCL3/VBLK3 60
3. VBLK: Vertical blank output. In this mode, the GPCL terminal is used to indicate the VBI
INTREQ4/GPCL4/VBLK4 41
of the output video. The beginning and end times of this signal are programmable via
I
2
C.
Copyright © 2007–2010, Texas Instruments Incorporated Device Details 7
Submit Documentation Feedback
Product Folder Link(s): TVP5154A