Datasheet
TVP5150AM1
www.ti.com
SLES209E–NOVEMBER 2007– REVISED OCTOBER 2011
4.4 Electrical Characteristics
DVDD = 1.8 V, PLL_AVDD = 1.8 V, CH_AVDD = 1.8 V, IO_DVDD = 3.3 V
For minimum/maximum values T
A
= 0°C to 70°C for commercial or T
A
= –40°C to 85°C for industrial, for typical
values T
A
= 25°C (unless otherwise noted)
4.5 DC Electrical Characteristics
TEST
PARAMETER MIN TYP MAX UNIT
CONDITIONS
(1)
I
DD(IO_D)
3.3-V I/O digital supply current Color bar input
(2)
4.8 6.2 mA
I
DD(D)
1.8-V digital supply current Color bar input
(2)
25.3 32.9 mA
I
DD(PLL_A)
1.8-V analog PLL supply current Color bar input
(2)
5.4 7.1 mA
I
DD(CH_A)
1.8-V analog core supply current Color bar input
(2)
24.4 31.7 mA
P
TOT
Total power dissipation, normal mode Color bar input
(2)
115 150 mW
P
DOWN
Total power dissipation, power-down mode
(3)
Color bar input 1 mW
C
i
Input capacitance By design 8 pF
V
OH
Output voltage high I
OH
= 2 mA 0.8 IO_DVDD V
V
OL
Output voltage low I
OL
= –2 mA 0.22 IO_DVDD V
V
OH_SCLK
SCLK output voltage high I
OH
= 4 mA 0.8 IO_DVDD V
V
OL_SCLK
SCLK output voltage low I
OL
= –4 mA 0.22 IO_DVDD V
I
IH
High-level input current
(4)
V
I
= V
IH
±20 µA
I
IL
Low-level input current
(4)
V
I
= V
IL
±20 µA
(1) Measured with a load of 15 pF
(2) For typical measurements only
(3) Assured by device characterization
(4) YOUT7 is a bidirectional terminal with an internal pulldown resistor. This terminal may sink more than the specified current when in
RESET mode.
4.6 Analog Electrical Characteristics
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Z
i
Input impedance, analog video inputs By design 500 kΩ
C
i
Input capacitance, analog video inputs By design 10 pF
V
i(pp)
Input voltage range
(1)
C
coupling
= 0.1 µF 0 0.75 V
ΔG Gain control maximum 12 dB
ΔG Gain control minimum 0 dB
DNL DC differential nonlinearity ADC only ±0.5 ±1 LSB
INL DC integral nonlinearity ADC only ±1 ±2.5 LSB
Fr Frequency response 6 MHz, Specified by design –0.9 –3 dB
SNR Signal-to-noise ratio 6 MHz, 1.0 V
P-P
50 dB
NS Noise spectrum 50% flat field 50 dB
DP Differential phase 1.5 °
DG Differential gain 0.5 %
(1) The 0.75-V maximum applies to the sync-chroma amplitude, not sync-white. The recommended termination resistors are 37.4 Ω, as
seen in Section 6.
Copyright © 2007–2011, Texas Instruments Incorporated Electrical Specifications 75
Submit Documentation Feedback
www.ti.com: TVP5150AM1