Datasheet
SLLS363A − SEPTEMBER 1999 − REVISED NOVEMBER 2000
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended ranges of operating conditions (unless otherwise
noted) (continued)
device
PARAMETER TEST CONDITION MIN TYP MAX UNIT
See Note 3 280
I
DD
Supply current
See Note 4
204
mA
I
DD
Supply current
See Note 5 164
mA
I
CC−ULP
Supply current − ultralow power mode
V
CC
= 3.3 V, T
A
= 25°C,
Ports disabled, PD = 0 V,
LPS = 0 V
150 µA
V
TH
Power status threshold, CPS input
†
400-kΩ resistor
†
4.7 7.5 V
High-level output voltage, CTL0, CTL1,
V
DD
= 2.7 V, I
OH
= −4 mA 2.2
V
OH
High-level output voltage, CTL0, CTL1,
D0−D7, DNA, C/LKON, SYSCLK outputs
V
DD
= 3 V to 3.6 V,
I
OH
= −4 mA
2.8
V
V
OL
Low-level output voltage, CTL0, CTL1,
D0−D7, DNA, C/LKON, SYSCLK outputs
I
OL
= 4 mA 0.4 V
V
OH-AJ
High-level Annex J output voltage, CTL0,
CTL1, D0−D7, DNA, C/LKON, SYSCLK
outputs
Annex J; I
OH
= −9 mA
,
ISO
= 0 V, V
DD_5V
= V
DD
,
V
DD
≥ 3 V
V
DD
−0.4 V
V
OL-AJ
Low-level Annex J output voltage, CTL0,
CTL1, D0−D7, DNA, C/LKON, SYSCLK
outputs
Annex J; I
OL
= 9 mA
,
ISO
= 0 V, V
DD_5V
= V
DD
,
V
DD
≥ 3 V
0.4 V
I
BH+
Positive peak bus holder current
(D0 − D7, CTL0, CTL1, LREQ)
ISO = 3.6 V, V
DD
= 3.6 V,
V
I
= 0 V to V
DD
,
0.05 1
mA
I
BH−
Negative peak bus holder current
(D0 − D7, CTL0, CTL1, LREQ, LPS, PD)
DD
V
I
= 0 V to V
DD
,
V
DD_5V
= V
DD
−1 −0.05
mA
I
I
Input current, LREQ, LPS, PD, TESTM,
SE, SM, PC0−PC2 inputs
ISO = 0 V, V
DD
3.6 V 5 µA
I
OZ
Off-state output current, CTL0, CTL1,
D0−D7, C/LKON I/Os
V
O
= V
DD
or 0 V ±5 µA
I
IRST
Pullup current, RESET input V
I
= 1.5 V or 0 V −90 −20 µA
I
SE-PU
Pullup current, SE input V
I
= 1.5 V or 0 V −50 −5 µA
V
IT+
Positive input threshold voltage, LREQ,
CTL0, CTL1, D0−D7 inputs
‡
ISO = 0 V ,V
DD_5V
= V
DD
V
DD
/2+0.3 V
DD
/2+0.9
V
V
IT+
Positive input threshold voltage, LPS
inputs
ISO = 0 V, V
DD_5V
= V
DD
,
V
ref
= V
DD
× 0.42
V
ref
+1
V
V
IT−
Negative input threshold voltage, LREQ,
CTL0, CTL1, D0−D7 inputs
‡
ISO = 0 V,V
DD_5V
= V
DD
V
DD
/2−0.9 V
DD
/2−0.3
V
V
IT−
Negative input threshold voltage, LPS
inputs
ISO = 0 V, V
DD_5V
= V
DD
,
V
ref
= V
DD
× 0.42
V
ref
+0.2
V
V
O
TPBIAS output voltage At rated I
O
current 1.665 2.015 V
†
Measured at cable power side of resistor.
‡
This parameter applicable only when ISO
low.
NOTES: 3. Transmit max packet (6 ports transmitting maximum size isochronous packets − 4096 bytes, sent on every isochronous internal,
S400, data value of 0xCCC CCCCh), V
DD
= 3.3 V, T
A
= 25°C.
4. Repeat typical packet (1 port receiving DV packets on every isochronous interval, 2 ports repeating the packet S100)
5. Idle (receive cycle start on port0, xmt cycle start on ports 1 through 5), V
DD
= 3.3 V, T
A
= 25°C.