Datasheet

www.ti.com
TS5A3159-EP
1- Ω SPDT ANALOG SWITCH
SCDS217B – DECEMBER 2005 – REVISED JANUARY 2006
PIN DESCRIPTION
PIN
NAME DESCRIPTION
NO.
1 NO Normally open
2 GND Digital ground
3 NC Normally closed
4 COM Common
5 V
+
Power supply
6 IN Digital control to connect COM to NO or NC
PARAMETER DESCRIPTION
SYMBOL DESCRIPTION
V
COM
Voltage at COM
V
NC
Voltage at NC
V
NO
Voltage at NO
r
on
Resistance between COM and NO ports when the channel is ON
r
peak
Peak on-state resistance over a specified voltage range
∆ r
on
Difference of r
on
between channels in a specific device
r
on(flat)
Difference between the maximum and minimum value of r
on
in a channel over the specified range of conditions
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the OFF state under
I
NC(OFF)
worst-case input and output conditions
I
NO(OFF)
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the OFF state
Leakage current measured at the NC port, with the corresponding channel (NC to COM) in the ON state and the output
I
NC(ON)
(COM) open
Leakage current measured at the NO port, with the corresponding channel (NO to COM) in the ON state and the output
I
NO(ON)
(COM) open
Leakage current measured at the COM port, with the corresponding channel (COM to NO) in the ON state and the output
I
COM(ON)
(NO) open
V
IH
Minimum input voltage for logic high for the control input (IN)
V
IL
Maximum input voltage for logic low for the control input (IN)
V
IN
Voltage at IN
I
IH
, I
IL
Leakage current measured at IN
Turn-on time for the switch. This parameter is measured under the specified range of conditions and by the propagation
t
ON
delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning ON.
Turn-off time for the switch. This parameter is measured under the specified range of conditions and by the propagation
t
OFF
delay between the digital control (IN) signal and analog output (COM or NO) signal when the switch is turning OFF.
Break-before-make time. This parameter is measured under the specified range of conditions and by the propagation
t
BBM
delay between the output of two adjacent analog channels (NC and NO), when the control signal changes state.
Charge injection is a measurement of unwanted signal coupling from the control (IN) input to the analog (NO or COM)
Q
C
output. This is measured in coulomb (C) and measured by the total charge induced due to switching of the control
input.Charge injection, Q
C
= C
L
× ∆ V
COM
, C
L
is the load capacitance and ∆ V
COM
is the change in analog output voltage.
C
NC(OFF)
Capacitance at the NC port when the corresponding channel (NC to COM) is OFF
C
NO(OFF)
Capacitance at the NO port when the corresponding channel (NO to COM) is OFF
C
NC(ON)
Capacitance at the NC port when the corresponding channel (NC to COM) is ON
C
NO(ON)
Capacitance at the NO port when the corresponding channel (NO to COM) is ON
C
COM(ON)
Capacitance at the COM port when the corresponding channel (COM to NO) is ON
C
IN
Capacitance of IN
OFF isolation of the switch is a measurement of OFF-state switch impedance. This is measured in dB in a specific
O
ISO
frequency, with the corresponding channel (NO to COM) in the OFF state.
Crosstalk is a measurement of unwanted signal coupling from an ON channel to an adjacent ON channel (NC1 to NC2).
X
TALK
This is measured in a specific frequency and in dB.
BW Bandwidth of the switch. This is the frequency in which the gain of an ON channel is –3 dB below the DC gain.
13
Submit Documentation Feedback