Datasheet
ELECTRICAL CHARACTERISTICS FOR 5-V SUPPLY
(1)
TS5A21366
SCDS285A – MARCH 2009 – REVISED OCTOBER 2009 .................................................................................................................................................
www.ti.com
V
+
= 4.5 V to 5.5 V, T
A
= – 40 ° C to 85 ° C (unless otherwise noted)
PARAMETER SYMBOL TEST CONDITIONS T
A
V
+
MIN TYP MAX UNIT
Analog Switch
V
COM
,
Analog signal range 0 V
+
V
V
NO
25 ° C 0.75 1
V
NO
= 2.5 V, Switch ON,
ON-state resistance r
on
4.5 V Ω
I
COM
= – 100 mA, See Figure 15
Full 1.4
ON-state resistance 25 ° C 0.04 0.1
V
NO
= 2.5 V, Switch ON,
match between Δ r
on
4.5 V Ω
I
COM
= – 100 mA, See Figure 15
Full 0.1
channels
25 ° C 0.15 0.25
ON-state resistance V
NO
= 1 V, 1.5 V, 2.5 V, Switch ON,
r
on(flat)
4.5 V Ω
flatness I
COM
= – 100 mA, See Figure 15
Full 0.25
V
NO
= 1 V, – 10 1.4 10
V
COM
= 4.5 V,
I
NO(OFF)
or 25 ° C 5.5 V nA
– 235 235
NO OFF leakage Switch OFF,
V
NO
= 4.5 V,
current See Figure 16
V
COM
= 1 V,
– 5 0.06 5
V
NO
= 0 to 5.5 V,
I
NO(PWROFF)
Full 0 V µ A
V
COM
= 5.5 V to 0,
– 10 10
V
COM
= 1 V, 25 ° C – 10 1.4 10
V
NO
= 4.5 V,
I
COM(OFF)
or 5.5 V nA
Full – 235 235
COM OFF leakage Switch OFF,
V
COM
= 4.5 V,
current See Figure 16
V
NO
= 1 V,
25 ° C – 5 0.06 5
V
NO
= 0 to 5.5 V,
I
COM(PWROFF)
0 V µ A
V
COM
= 5.5 V to 0,
Full – 10 10
V
NO
= 1 V, 25 ° C – 5 1.33 5
V
COM
= Open,
NO ON leakage Switch ON,
I
NO(ON)
or 5.5 V nA
current See Figure 17
Full – 50 50
V
NO
= 4.5 V,
V
COM
= Open,
V
COM
= 1 V, 25 ° C – 5 1.33 5
V
NO
= Open,
COM Switch ON,
I
COM(ON)
or 5.5 V nA
ON leakage current See Figure 17
Full – 50 50
V
COM
= 4.5 V,
V
NO
= Open,
Digital Control Inputs (IN1, IN2)
(2)
Input logic high V
IH
Full 5.5 V 1.05 5.5 V
Input logic low V
IL
Full 5.5 V 0 0.6 V
Input leakage current I
IH
, I
IL
V
I
= 1.95 V or GND Full 5.5 V – 0.6 0.6 µ A
Input resistance r
IN
V
I
= 1.95 V Full 5.5 V 6 M Ω
(1) The algebraic convention, whereby the most negative value is a minimum and the most positive value is a maximum
(2) All unused digital inputs of the device must be held at V
+
or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4 Submit Documentation Feedback Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TS5A21366