Datasheet

www.ti.com
Electrical Characteristics
Switching Characteristics
Dynamic Characteristics
TS3V330
QUAD SPDT WIDE-BANDWIDTH VIDEO SWITCH
WITH LOW ON-STATE RESISTANCE
SCDS162C – MAY 2004 – REVISED JULY 2005
over recommended operating free-air temperature range, V
CC
= 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER TEST CONDITIONS
(1)
MIN TYP
(2)
MAX UNIT
V
IK
EN, IN V
CC
= 3 V, I
IN
= –18 mA –1.8 V
V
hys
EN, IN 150 mV
I
IH
EN, IN V
CC
= 3.6 V, V
IN
and V
EN
= V
CC
± 1 µ A
I
IL
EN, IN V
CC
= 3.6 V, V
IN
and V
EN
= GND ± 1 µ A
I
OZ
(3)
V
CC
= 3.6 V, V
O
= 0 to 3.6 V, V
I
= 0, Switch OFF ± 1 µ A
I
OS
(4)
V
CC
= 3.6 V, V
O
= 0.5 V
CC,
V
I
= 0, Switch ON 50 mA
I
off
V
CC
= 0 V, V
O
= 0 to 3.6 V, V
I
= 0 15 µ A
I
CC
V
CC
= 3.6 V, I
I/O
= 0, Switch ON or OFF 10 µ A
∆ I
CC
EN, IN V
CC
= 3.6 V, One input at 3.4 V, Other inputs at V
CC
or GND 750 µ A
V
CC
= 3.6 V, V
EN
= GND D and S ports open,
mA/
I
CCD
0.45
MHz
V
IN
input switching 50% duty cycle
C
IN
EN, IN V
IN
of V
EN
= 0, f = 1 MHz 3.5 pF
D port 10
C
OFF
V
I
= 0, f = 1 MHz, Outputs open, Switch OFF pF
S port 5
C
ON
V
I
= 0, f = 1 MHz, Outputs open, Switch ON 17 pF
V
I
= 1 V, I
O
= 13 mA, R
L
= 75 Ω 5 7
r
on
(5)
V
CC
= 3 V Ω
V
I
= 2 V, I
O
= 26 mA, R
L
= 75 Ω 7 10
(1) V
I
, V
O
, I
I
, and I
O
refer to I/O pins.
(2) All typical values are at V
CC
= 5 V (unless otherwise noted), T
A
= 25 ° C.
(3) For I/O ports, I
OZ
includes the input leakage current.
(4) The I
OS
test is applicable to only one ON channel at a time. The duration of this test is less than one second.
(5) Measured by the voltage drop between the D and S terminals at the indicated current through the switch. ON-state resistance is
determined by the lower of the voltages of the two (D or S) terminals.
over recommended operating free-air temperature range, V
CC
= 3.3 V ± 0.3 V, R
L
= 75 Ω , C
L
= 20 pF (unless otherwise
noted) (see Figure 5 )
FROM TO
PARAMETER MIN TYP MAX UNIT
(INPUT) (OUTPUT)
t
ON
S D 2.5 6.5 ns
t
OFF
S D 1.1 3.5 ns
over recommended operating free-air temperature range, V
CC
= 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TYP
(1)
UNIT
D
G
(2)
R
L
= 150 Ω , f = 3.58 MHz, See Figure 6 0.82 %
D
P
(2)
R
L
= 150 Ω , f = 3.58 MHz, See Figure 6 0.1 Deg
BW R
L
= 150 Ω , See Figure 7 300 MHz
X
TALK
R
L
= 150 Ω , f = 10 MHz, RIN = 10 Ω , See Figure 8 –80 dB
O
IRR
R
L
= 150 Ω , f = 10 MHz, See Figure 9 –50 dB
(1) All typical values are at V
CC
= 5 V (unless otherwise noted), T
A
= 25 ° C.
(2) D
G
and D
P
are expressed in absolute magnitude.
6