Datasheet

www.ti.com
Electrical Characteristics
Electrical Characteristics
TS3L301
16-BIT TO 8-BIT SPDT GIGABIT LAN SWITCH
WITH LOW AND FLAT ON-STATE RESISTANCE
SCDS178C – NOVEMBER 2004 – REVISED APRIL 2006
for 1000 Base-T Ethernet switching over recommended operating free-air temperature range, V
DD
= 3.3 V ± 0.3 V
(unless otherwise noted)
PARAMETER TEST CONDITIONS
(1)
MIN TYP
(2)
MAX UNIT
V
IK
SEL V
DD
= 3.6 V, I
IN
= –18 mA –0.7 –1.2 V
I
IH
SEL V
DD
= 3.6 V, V
IN
= V
DD
± 1 µ A
I
IL
SEL V
DD
= 3.6 V, V
IN
= GND ± 1 µ A
I
off
V
DD
= 0, V
O
= 0 to 3.6 V, V
I
= 0 1 µ A
I
DD
V
DD
= 3.6 V, I
I/O
= 0, Switch ON or OFF 250 600 µ A
C
IN
SEL f = 1 MHz, V
IN
= 0 2.5 3 pF
C
OFF
B port V
I
= 0, f = 1 MHz, Outputs open, Switch OFF 3.5 4 pF
C
ON
V
I
= 0, f = 1 MHz, Outputs open, Switch ON 10 10.9 pF
r
on
V
DD
= 3 V, 1.5 V ≤ V
I
≤ V
DD
, I
O
= –40 mA 4 8 Ω
r
on(flat)
(3)
V
DD
= 3 V, V
I
= 1.5 V and V
DD
, I
O
= –40 mA 0.7 Ω
∆ r
on
(4)
V
DD
= 3 V, 1.5 V ≤ V
I
≤ V
DD
, I
O
= –40 mA 0.2 1.2 Ω
(1) V
I
, V
O
, I
I
, and I
O
refer to I/O pins. V
IN
refers to the control inputs.
(2) All typical values are at V
DD
= 3.3 V (unless otherwise noted), T
A
= 25 ° C.
(3) r
on(flat)
is the difference of r
on
in a given channel at specified voltages.
(4) ∆ r
on
is the difference of r
on
from center (A
4
, A
5
) ports to any other port.
for 10/100 Base-T Ethernet switching over recommended operating free-air temperature range, V
DD
= 3.3 V ± 0.3 V
(unless otherwise noted)
PARAMETER TEST CONDITIONS
(1)
MIN TYP
(2)
MAX UNIT
V
IK
SEL V
DD
= 3.6 V, I
IN
= –18 mA –0.7 –1.2 V
I
IH
SEL V
DD
= 3.6 V, V
IN
= V
DD
± 1 µ A
I
IL
SEL V
DD
= 3.6 V, V
IN
= GND ± 1 µ A
I
off
V
DD
= 0, V
O
= 0 to 3.6 V, V
I
= 0 1 µ A
I
DD
V
DD
= 3.6 V, I
I/O
= 0, Switch ON or OFF 250 600 µ A
C
IN
SEL f = 1 MHz, V
IN
= 0 2.5 3 pF
C
OFF
B port V
I
= 0, f = 1 MHz, Outputs open, Switch OFF 3.5 4 pF
C
ON
V
I
= 0, f = 1 MHz, Outputs open, Switch ON 10 10.9 pF
r
on
V
DD
= 3 V, 1.25 V ≤ V
I
≤ V
DD
, I
O
= –10 mA to –30 mA 4 8 Ω
r
on(flat)
(3)
V
DD
= 3 V, V
I
= 1.25 V and V
DD
, I
O
= –10 mA to –30 mA 0.7 Ω
∆ r
on
(4)
V
DD
= 3 V, 1.25 V ≤ V
I
≤ V
DD
, I
O
= –10 mA to –30 mA 0.2 1.2 Ω
(1) V
I
, V
O
, I
I
, and I
O
refer to I/O pins. V
IN
refers to the control inputs.
(2) All typical values are at V
DD
= 3.3 V (unless otherwise noted), T
A
= 25 ° C.
(3) r
on(flat)
is the difference of r
on
in a given channel at specified voltages.
(4) ∆ r
on
is the difference of r
on
from center (A
4
, A
5
) ports to any other port.
4
Submit Documentation Feedback