Datasheet

TS3L110
QUAD SPDT HIGH-BANDWIDTH 10/100 BASE-T LAN SWITCH
DIFFERENTIAL 8-CHANNEL TO 4-CHANNEL MULTIPLEXER/DEMULTIPLEXER
SCDS176 − SEPTEMBER 2004
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range,
V
CC
= 3.3 V + 0.3 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP
†
MAX UNIT
V
IK
E, S V
CC
= 3.6 V, I
IN
= −18 mA −1.8 V
I
IH
E, S V
CC
= 3.6 V, V
IN
= 5.5 V ±1 μA
I
IL
E, S V
CC
= 3.6 V, V
IN
= GND ±1 μA
I
off
V
CC
= 0, V
O
= 0 to 5.5 V , V
I
= 0 1 μA
I
CC
V
CC
= 3.6 V, I
I/O
= 0, Switch ON or OFF 0.7 1.5 mA
C
in
E, S f = 1 MHz, V
IN
= 0 2.5 3.5 pF
C
I port V
I
= 0,
f = 1 MHz,
Outputs open,
Switch OFF 3.5 5
pF
C
io(OFF)
Y port V
I
= 0,
f = 1 MHz,
Outputs open,
Switch OFF 5.5 7
pF
C
io(ON)
I or Y port V
I
= 0,
f = 1 MHz,
Outputs open,
Switch ON 10.5 13 pF
r
on
V
CC
= 3 V 1.25 V ≤ V
I
≤ V
CC
, I
I
= −10 mA to −30 mA 4 8 Ω
r
on(flat)
‡
V
CC
= 3 V V
I
= 1.25 V and V
CC
, I
I
= −10 mA to −30 mA 1 Ω
Δr
on
§
V
CC
= 3 V, 1.25 V ≤ V
I
≤ V
CC
, I
I
= −10 mA to −30 mA 0.9 2 Ω
V
I
, V
O
, I
I
, and I
O
refer to I/O pins. V
IN
refers to the control inputs.
†
All typical values are at V
CC
= 3.3 V (unless otherwise noted), T
A
= 25°C.
‡
r
on(flat)
is the difference of r
on
in a given channel at specified voltages.
§
Δr
on
is the difference of r
on
in a given device.
switching characteristics over recommended operating free-air temperature range,
V
CC
= 3.3 V + 0.3 V, R
L
= 200 Ω, C
L
= 10 pF (unless otherwise noted) (see Figures 5 and 6)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
MIN TYP
†
MAX UNIT
t
pd
¶
I or Y
Y or I 0.25 ns
t
PZH
, t
PZL
E or S
I or Y 0.5 7 ns
t
PHZ
, t
PLZ
E or S
I or Y 0.5 5 ns
t
sk(p)
#
I or Y
Y or I 0.1 0.2 ns
†
All typical values are at V
CC
= 3.3 V (unless otherwise noted), T
A
= 25°C.
¶
The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance when
driven by an ideal voltage source (zero output impedance).
#
Skew between opposite transitions of the same output |t
PHL
− t
PLH
|. This parameter is not production tested.
dynamic characteristics over recommended operating free-air temperature range,
V
CC
= 3.3 V + 0.3 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP
†
MAX UNIT
X
TALK
R
L
= 100 Ω, f = 250 MHz, see Figure 7 −26 dB
O
IRR
R
L
= 100 Ω, f = 250 MHz, see Figure 8 −28 dB
BW R
L
= 100 Ω, see Figure 6 500 MHz
†
All typical values are at V
CC
= 3.3 V (unless otherwise noted), T
A
= 25°C.