Datasheet

TS3DV621
SCDS330C –JANUARY 2012–REVISED MAY 2013 www.ti.com
ELECTRICAL CHARACTERISTICS
PARAMETER TEST CONDITIONS
(1)
MIN TYP
(2)
MAX UNIT
V
IK
Digital input clamp voltage SEL1,SEL2 V
CC
= 3.6 V, I
IN
= -18 mA – 1. 2 – 0. 8 V
R
ON
On-state resistance All I/O V
CC
= 3 V, 1.5 V ≤ V
I/O
≤ V
CC
, I
I/O
= –40 mA 8 12 Ω
V
CC
= 3 V, VI/O = 1.5 V and V
CC
,
R
ON(flat)
(3)
On-state resistance flatness All I/O 1.5 Ω
I
I/O
= –40mA
On-state resistance match
ΔR
ON
(4)
All I/O V
CC
= 3 V, 1.5 V ≤ V
I/O
≤ V
CC
, I
I/O
= –40mA 0.4 1 Ω
between channels
Digital input high leakage
I
IH
SEL1,SEL2 V
CC
= 3.6 V , V
IN
= V
DD
±1 µA
current
Digital input low leakage
I
IL
SEL1,SEL2 V
CC
= 3.6 V, V
IN
= GND ±1 µA
current
Leakage under power off
I
OFF
All outputs V
CC
= 0 V, V
I/O
= 0 to 3.6 V, V
IN
= 0 to 5.5V ±1 µA
conditions
C
IN
Digital input capacitance SEL1,SEL2 f = 1 MHz, V
IN
= 0 V 2.6 3.2 pF
f = 1 MHz, V
I/O
= 0 V, Output is open,
C
OFF
Switch OFF capacitance All I/O 2 pF
Switch is OFF
f = 1 MHz, V
I/O
= 0 V, Output is open,
C
ON
Switch ON capacitance All I/O 5.6 pF
Switch is ON
I
CC
VCC supply current V
CC
= 3.6 V, I
I/O
= 0, V
IN
= V
DD
or GND 300 400 µA
(1) V
I
, V
O
, I
I
, and I
O
refer to I/O pins, V
IN
refers to the control inputs
(2) All typical values are at V
CC
= 3.3V (unless otherwise noted), T
A
= 25°C
(3) R
ON(FLAT)
is the difference of R
ON
in a given channel at specified voltages.
(4) ΔR
ON
is the difference of R
ON
from center port to any other ports.
SWITCHING CHARACTERISTICS
Over recommended operation free-air temperature range, V
CC
= 3.3 V ± 0.3 V, R
L
= 200 Ω, C
L
= 4 pF (unless otherwise
noted) (see and )
FROM TO
PARAMETER MIN TYP
(1)
MAX UNIT
(INPUT) (OUTPUT)
t
pd
(2)
All I/O input side All I/O output side 40 ps
t
PZH
, t
PZL
SEL1, SEL2 All I/O 2 7 ns
t
PHZ
, t
PLZ
SEL1, SEL2 All I/O 2 5 ns
t
sk(o)
(3)
All I/O input side All I/O output side 6 30 ps
t
sk(p)
(4)
6 30 ps
(1) All typical values are at V
CC
= 3.3 V (unless otherwise noted), T
A
= 25°C.
(2) The propagation delay is the calculated RC time constant of the typical ON-State resistance of the switch and the specified load
capacitance when driven by an ideal voltage source (zero output impedance).
(3) Output skew between center port and any other channel.
(4) Skew between opposite transitions of the same output |t
PHL
– t
PLH
|
DYNAMIC CHARACTERISTICS
Over recommended operation free-air temperature range, V
CC
= 3.3 V ± 0.3 V (unless otherwise noted)
PARAMETER TEST CONDITIONS TYP
(1)
UNIT
XTALK R
L
= 50 Ω, f = 250 MHz (Figure 11) –43 dB
OIRR R
L
= 50 Ω, f = 250 MHz (Figure 12) –42 dB
BW R
L
= 50 Ω, Switch ON (Figure 10) 2.2 GHz
(1) All typical values are at V
CC
= 3.3 V (unless otherwise noted), T
A
= 25°C.
6 Submit Documentation Feedback Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links :TS3DV621