User's Manual
Table Of Contents
- Table of Contents
- Preface
- 1 Introduction and Description
- 2 Using the EVM
- 3 EVM Software
- 3.1 Software Installations
- 3.2 Software Installation for Rev. A EVM
- 3.3 Software Interface
- 3.4 Set Protocol
- 3.5 ISO/IEC 15693 Protocol
- 3.5.1 Inventory
- 3.5.2 Read Single Block
- 3.5.3 Write Single Block
- 3.5.4 Lock Block
- 3.5.5 Read Multiple Blocks
- 3.5.6 Write Multiple Blocks
- 3.5.7 Stay Quiet
- 3.5.8 Select
- 3.5.9 Reset to Ready
- 3.5.10 Write AFI (Application Family Identifier)
- 3.5.11 Lock AFI (Application Family Identifier)
- 3.5.12 Write DSFID (Data Storage Format ID)
- 3.5.13 Lock DSFID (Data Storage Format ID)
- 3.5.14 Get System Info
- 3.5.15 Get Multiple-Block Security Status (Get Mult_Blk Sel Status)
- 3.6 ISO/IEC 14443A Protocol
- 3.7 ISO/IEC 14443B Protocol
- 3.8 Tag-it Protocol
- 3.9 Find Tags
- 3.10 Registers
- 3.11 Test
- A ISO/IEC 15693 Reference Material
- B Tag-it Reference Material
- Important Notices
3.11Test
Test
www.ti.com
Ifdesired,theusercansendmanualcommandsbyusingTesttab.Onlythecommand+parametersfield
mustbetypedin.Allotherfieldsintheprotocolcanbeleftout:
SOF(0x01)Numberofbytes0x000x0304Command+parametersEOF(0x0000)
ThecommunicationstartswithSOF(0x01).Thesecondbytedefinesthenumberofbytesintheframe
includingSOF.Thethirdbyteshouldbekeptat0x00,fourthbyteat0x03andthefifthbyteat0x04.The
sixthbyteisthecommandcode,whichisfollowedbyparametersordata.Thecommunicationendswith2
bytesof0x00.
CommandParametersExample
0x03TRF796xenable/disable0x00–Readerenable010900030403FF0000
0xFF–Readerdisable
0x0FDirectmode01080003040F0000
0x10WritesingleregisterAddress,data,address,data...010A0003041015670000
0x11WritecontinuousAddress,data,data...010C00030411136746A40000
0x12ReadsingleregisterAddress,address,...010B00030412010A130000
0x13ReadcontinuousNR.ofbytestoread,startaddress010A0003041305030000
0x14Inventory(ISO15693)FIFOdata010B000304140601000000
0x15DirectcommandDirectcommandcode0109000304150F0000
0x16WriterawDataorcommands...011000030416913D0040AABBCCDD0000
0x18RequestcommandISOFlags,commandcode,data,...(as010B000304180620010000
15693,Tag-it,14443BHaltspecifiedinISOandTag-it)
0x34SIDpoll(Tag-it)Flags,commandcode,mask(as010B000304340050000000
specifiedinTag-it)
0x54Beginround(EPC)No.ofslots010900030454030000
0x55Closeslotsequence(EPC)0108000304550000
0xA0REQA(14443A)0108000304A00000
0xA2Select(14443A)CID010D000304A211223344440000
0xB0REQB(14443B)0108000304B00000
0xF0AGCselection0x00–AGCenable0109000304F0FF0000
0xFF–AGCdisable
0xF1AM/PMinputselection0x00–FMinput0109000304F1000000
0xFF–AMinput
0xFEGetVersion0108000304FE0000
90EVMSoftwareSLOU192C–November2006–RevisedDecember2008
SubmitDocumentationFeedback