Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsPMICsPMIC - LDO voltage regulator Negative, adjustable MSOP 8 PowerPad

GND

OUT

NR/SS

DNC

DGNPACKAGE

3mm 5mmMSOP-8PowerPAD

(TOPVIEW)

TPS7A49

+18V

OUT

EN GND

-18V

TPS7A30

IN OUT

EN GND

EVM

+15V

-15V

TPS7A30xx

www.ti.com

SBVS125B –AUGUST 2010–REVISED DECEMBER 2013

–36V, –200mA, Ultralow-Noise, Negative Linear Regulator

FEATURES

DESCRIPTION

The TPS7A30xx series of devices are negative, high-

• Input Voltage Range: –3V to –36V

voltage (–36V), ultralow-noise (15.1μV

RMS

, 72dB

• Noise:

PSRR) linear regulators capable of sourcing a

– 14μV

RMS

(20Hz to 20kHz)

maximum load of 200mA.

– 15.1μV

RMS

(10Hz to 100kHz)

These linear regulators include a CMOS logic-level-

• Power-Supply Ripple Rejection:

compatible enable pin and capacitor-programmable

soft-start function that allows for customized power-

– 72dB (120Hz)

management schemes. Other features available

– ≥ 55dB (10Hz to 700kHz)

include built-in current limit and thermal shutdown

• Adjustable Output: –1.18V to –33V

protection to safeguard the device and system during

fault conditions.

• Maximum Output Current: 200mA

• Dropout Voltage: 216mV at 100mA

The TPS7A30xx family is designed using bipolar

technology, and is ideal for high-accuracy, high-

• Stable with Ceramic Capacitors ≥ 2.2μF

precision instrumentation applications where clean

• CMOS Logic-Level-Compatible Enable Pin

voltage rails are critical to maximize system

• Built-In, Fixed, Current-Limit and Thermal

performance. This design makes it an excellent

Shutdown Protection

choice to power operational amplifiers, analog-to-

digital converters (ADCs), digital-to-analog converters

• Available in High Thermal Performance

(DACs), and other high-performance analog circuitry.

MSOP-8 PowerPAD™ Package

In addition, the TPS7A30xx family of linear regulators

• Operating Temperature Range:

is suitable for post dc/dc converter regulation. By

–40°C to +125°C

filtering out the output voltage ripple inherent to dc/dc

switching conversion, maximum system performance

APPLICATIONS

is provided in sensitive instrumentation, test and

• Supply Rails for Op Amps, DACs, ADCs, and

measurement, audio, and RF applications.

Other High-Precision Analog Circuitry

For applications where positive and negative high-

• Audio

performance rails are required, consider TI’s

TPS7A49xx family of positive high-voltage, ultralow-

• Post DC/DC Converter Regulation and Ripple

noise linear regulators.

Filtering

• Test and Measurement

Figure 1. Typical Application

• RX, TX, and PA Circuitry

• Industrial Instrumention

• Base Stations and Telecom Infrastrucure

• –12V and –24V Industrial Buses

Post DC/DC Converter Regulation for High-

Performance Analog Circuitry

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2PowerPAD is a trademark of Texas Instruments.

3All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (25 pages)

PAGE 1
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 –36V, –200mA, Ultralow-Noise, Negative Linear Regulator FEATURES DESCRIPTION • • The TPS7A30xx series of devices are negative, highvoltage (–36V), ultralow-noise (15.1μVRMS, 72dB PSRR) linear regulators capable of sourcing a maximum load of 200mA. 1 23 • • • • • • • • • Input Voltage Range: –3V to –36V Noise: – 14μVRMS (20Hz to 20kHz) – 15.
PAGE 2
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure.
PAGE 3
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 ELECTRICAL CHARACTERISTICS (1) At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2µF, COUT = 2.2µF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. TPS7A30xx PARAMETER VIN Input voltage range VREF Internal reference Output voltage range TEST CONDITIONS MIN TYP –35.0 (2) TJ = +25°C, VNR/SS = VREF –1.202 |VIN| ≥ |VOUT(NOM)| + 1.0V –1.
PAGE 4
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.
PAGE 5
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 PIN CONFIGURATION DGN PACKAGE MSOP-8 (TOP VIEW) OUT FB NC GND 1 2 3 4 8 7 6 5 IN DNC NR/SS EN PIN DESCRIPTIONS TPS7A30xx NAME NO. OUT 1 Regulator output. A capacitor ≥ 2.2µF must be tied from this pin to ground to assure stability. DESCRIPTION FB 2 This pin is the input to the control-loop error amplifier. It is used to set the output voltage of the device. NC 3 Not internally connected.
PAGE 6
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com TYPICAL CHARACTERISTICS At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2μF, COUT = 2.2μF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. FEEDBACK VOLTAGE vs INPUT VOLTAGE FEEDBACK CURRENT vs TEMPERATURE -1.165 100 90 80 70 IFB (nA) VFB (V) -1.17 -1.175 +125°C +105°C +85°C +25°C -40°C -1.18 60 50 40 30 20 10 -1.
PAGE 7
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 TYPICAL CHARACTERISTICS (continued) At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2μF, COUT = 2.2μF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. QUIESCENT CURRENT vs INPUT VOLTAGE SHUTDOWN CURRENT vs INPUT VOLTAGE 100 3.5 90 +125°C +105°C +85°C +25°C -40°C 3 80 2.
PAGE 8
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2μF, COUT = 2.2μF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. ENABLE THRESHOLD VOLTAGE vs TEMPERATURE POWER-SUPPLY REJECTION RATIO vs COUT 90 2 ON 80 1 70 0.5 60 0 PSRR (dB) VEN (V) 1.5 OFF -0.5 50 40 30 -1 -1.
PAGE 9
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 TYPICAL CHARACTERISTICS (continued) At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2μF, COUT = 2.2μF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. Output Spectral Noise Density (mV/ÖHz) OUTPUT SPECTRAL NOISE DENSITY vs OUTPUT CURRENT 10 VOUT = -1.
PAGE 10
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com TYPICAL CHARACTERISTICS (continued) At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2μF, COUT = 2.2μF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. CAPACITOR-PROGRAMMABLE SOFT START VOUT = -1.2V VIN = -3V IOUT = 1mA CIN = COUT = 2.
PAGE 11
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 TYPICAL CHARACTERISTICS (continued) At TJ = –40°C to +125°C, |VIN| = |VOUT(NOM)| + 1.0V or |VIN| = 3.0V (whichever is greater), VEN = VIN, IOUT = 1mA, CIN = 2.2μF, COUT = 2.2μF, CNR/SS = 0nF, and the FB pin tied to OUT, unless otherwise noted. 50mV/div 200mA/div LOAD TRANSIENT RESPONSE IOUT VOUT VIN = -3.0V IOUT = 1mA to 200mA COUT = 2.2mF Time (100ms/div) Figure 29.
PAGE 12
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com THEORY OF OPERATION GENERAL DESCRIPTION The TPS7A30xx belongs to a family of new generation linear regulators that use an innovative bipolar process to achieve ultralow-noise and very high PSRR levels at a wide input voltage range. These features, combined with a high thermal performance MSOP-8 with PowerPAD package make this device ideal for high-performance analog applications.
PAGE 13
TPS7A30xx www.ti.com OUTPUT NOISE The TPS7A30xx provides low output noise when a noise reduction capacitor (CNR/SS) is used. The noise reduction capacitor serves as a filter for the internal reference. By using a 0.01μF noise reduction capacitor, the output noise is reduced by almost 80% (from 80μVRMS to 17μVRMS); see Figure 21. SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 Additionally, ac performance can be maximized by adding a 0.01μF bypass capacitor (CBYP) from the FB pin to the OUT pin.
PAGE 14
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com APPLICATION INFORMATION POWER FOR PRECISION ANALOG One of the primary TPS7A30xx applications is to provide ultralow noise voltage rails to highperformance analog circuitry in order to maximize system accuracy and precision.
PAGE 15
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 LAYOUT PACKAGE MOUNTING Solder pad footprint recommendations for the TPS7A30xx are available at the end of this product datasheet and at www.ti.com.
PAGE 16
TPS7A30xx SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 www.ti.com Figure 33. PCB Layout Example U1 TPS7A30XXDGN 5 6 C4 7 8 Vin J1 4 GND EN 3 NR/SS NC DNC FB 2 IN PwPd J1 1 OUT C1 J7 GND R1 9 J4 C2 C3 R3 Figure 34.
PAGE 17
TPS7A30xx www.ti.com SBVS125B – AUGUST 2010 – REVISED DECEMBER 2013 REVISION HISTORY NOTE: Page numbers for previous revisions may differ from the page numbers in the current version. Changes from Revision A (March 2011) to Revision B • Page Changed VREF parameter typical specification in Electrical Characteristics table ................................................................ 3 Changes from Original (August 2010) to Revision A • Page Switched colors for 10mA and 200mA curves in Figure 11 ...
PAGE 18
PACKAGE OPTION ADDENDUM www.ti.
PAGE 19
PACKAGE OPTION ADDENDUM www.ti.com 6-Nov-2013 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
PAGE 20
PACKAGE MATERIALS INFORMATION www.ti.com 6-Nov-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS7A3001DGNR MSOPPower PAD DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS7A3001DGNT MSOPPower PAD DGN 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.
PAGE 21
PACKAGE MATERIALS INFORMATION www.ti.com 6-Nov-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS7A3001DGNR MSOP-PowerPAD DGN 8 2500 367.0 367.0 35.0 TPS7A3001DGNT MSOP-PowerPAD DGN 8 250 210.0 185.0 35.
PAGE 22
PAGE 23
PAGE 24
PAGE 25
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.