Datasheet
ABSOLUTE MAXIMUM RATINGS
DISSIPATION RATINGS
RECOMMENDED OPERATING CONDITIONS
(1) To calculate the minimum input voltage for your maximum output current, use the following equation:
V =V +V
I(min) O(max) DO(max load)
TPS76615 , , TPS76618 , , TPS76625
TPS76627 , TPS76628 , TPS76630
TPS76633 , TPS76650 , TPS76601
SLVS237C – AUGUST 1999 – REVISED JANUARY 2009 .................................................................................................................................................
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION
(1)
PRODUCT V
OUT
(2)
XX is nominal output voltage (for example, 28 = 2.8V, 01 = Adjustable).
(3)
TPS766 xxyz Y is package designator.
Z is package quantity.
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com .
(2) Output voltages from 1.5 V to 5.0 V in 50-mV increments are available through the use of innovative factory EEPROM programming;
minimum order quantities may apply. Contact factory for details and availability.
(3) The TPS76601 is programmable using an external resistor divider (see Application Information ).
Over operating free-air temperature range (unless otherwise noted).
(1)
PARAMETER TPS766xx UNIT
V
I
Input voltage range
(2)
– 0.3 to 13.5 V
Voltage range at EN – 0.3 to 16.5 V
Maximum PG voltage 16.5 V
Peak output current Internally limited
Continuous total power dissipation See Dissipation Ratings Table
V
O
Output voltage (OUT, FB) 7 V
T
J
Operating virtual junction temperature range – 40 to +125 ° C
T
stg
Storage temperature range – 65 to +150 ° C
ESD rating, HBM 2 kV
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
(2) All voltage values are with respect to network terminal ground.
AIR FLOW T
A
< +25 ° C DERATING FACTOR T
A
= +70 ° C T
A
= +85 ° C
PACKAGE (CFM) POWER RATING ABOVE T
A
= +25 ° C POWER RATING POWER RATING
0 568 mW 5.68 mW/ ° C 312 mW 227 mW
D
250 904 mW 9.04 mW/ ° C 497 mW 361 mW
MIN MAX UNIT
V
I
Input voltage
(1)
2.7 10 V
V
O
Output voltage range 1.2 5.5 V
I
O
Output current
(2)
0 250 mA
T
J
Operating virtual junction temperature
(2)
– 40 125 ° C
(2) Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
2 Submit Documentation Feedback Copyright © 1999 – 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS76615 TPS76618 TPS76625 TPS76627 TPS76628 TPS76630 TPS76633 TPS76650
TPS76601