Datasheet

TPS742xx
SBVS064L –DECEMBER 2005–REVISED NOVEMBER 2010 www.ti.com
ELECTRICAL CHARACTERISTICS
At V
EN
= 1.1V, V
IN
= V
OUT
+ 0.3V, C
IN
= C
BIAS
= 0.1mF, C
OUT
= 10mF, I
OUT
= 50mA, V
BIAS
= 5.0V, and T
J
= –40°C to +125°C,
unless otherwise noted. Typical values are at T
J
= +25°C.
TPS742xx
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
IN
Input voltage range V
OUT
+ V
DO
5.5 V
V
BIAS
Bias pin voltage range 2.375 5.25 V
V
REF
Internal reference (Adj.) T
J
= +25°C 0.796 0.8 0.804 V
Output voltage range V
IN
= 5V, I
OUT
= 1.5A, V
BIAS
= 5V V
REF
3.6 V
V
OUT
2.375V ≤ V
BIAS
≤ 5.25V, V
OUT
+ 1.62V ≤ V
BIAS
Accuracy
(1)
–1 ±0.2 1 %
50mA ≤ I
OUT
≤ 1.5A
V
OUT (NOM)
+ 0.3 ≤ V
IN
≤ 5.5V, QFN 0.0005 0.05
V
OUT
/V
IN
Line regulation %/V
V
OUT (NOM)
+ 0.3 ≤ V
IN
≤ 5.5V, DDPAK 0.0005 0.06
0mA ≤ I
OUT
≤ 50mA 0.013 %/mA
V
OUT
/I
OUT
Load regulation
50mA ≤ I
OUT
≤ 1.5A 0.04 %/A
I
OUT
= 1.5A, V
BIAS
– V
OUT (NOM)
≥ 1.62V, QFN 55 100 mV
V
IN
dropout voltage
(2)
V
DO
I
OUT
= 1.5A, V
BIAS
– V
OUT (NOM)
≥ 1.62V, DDPAK 60 120 mV
V
BIAS
dropout voltage
(2)
I
OUT
= 1.5A, V
IN
= V
BIAS
1.4 V
I
CL
Current limit V
OUT
= 80% × V
OUT (NOM)
1.8 4 A
I
BIAS
Bias pin current I
OUT
= 0mA to 1.5A 2 4 mA
Shutdown supply current
I
SHDN
V
EN
≤ 0.4V 1 100 mA
(V
IN
)
Feedback, Sense pin
I
FB
, I
SNS
I
OUT
= 50mA to 1.5A –250 68 250 nA
current
(3)
1kHz, I
OUT
= 1.5A, V
IN
= 1.8V, V
OUT
= 1.5V 73
Power-supply rejection
dB
(V
IN
to V
OUT
)
300kHz, I
OUT
= 1.5A, V
IN
= 1.8V, V
OUT
= 1.5V 42
PSRR
1kHz, I
OUT
= 1.5A, V
IN
= 1.8V, V
OUT
= 1.5V 62
Power-supply rejection
dB
(V
BIAS
to V
OUT
)
300kHz, I
OUT
= 1.5A, V
IN
= 1.8V, V
OUT
= 1.5V 50
Noise Output noise voltage 100Hz to 100kHz, I
OUT
= 1.5A, C
SS
= 0.001mF 16 × V
OUT
mV
RMS
%V
OUT
droop during load
V
TRAN
I
OUT
= 50mA to 1.5A at 1A/ms, C
OUT
= none 3.5 %V
OUT
transient
t
STR
Minimum startup time I
OUT
= 1.5A, C
SS
= open 100 ms
I
SS
Soft-start charging current V
SS
= 0.4V 0.5 0.73 1 mA
V
EN, HI
Enable input high level 1.1 5.5 V
V
EN, LO
Enable input low level 0 0.4 V
V
EN, HYS
Enable pin hysteresis 50 mV
V
EN, DG
Enable pin deglitch time 20 ms
I
EN
Enable pin current V
EN
= 5V 0.1 1 mA
V
IT
PG trip threshold V
OUT
decreasing 86.5 90 93.5 %V
OUT
V
HYS
PG trip hysteresis 3 %V
OUT
V
PG, LO
PG output low voltage I
PG
= 1mA (sinking), V
OUT
< V
IT
0.3 V
I
PG, LKG
PG leakage current V
PG
= 5.25V, V
OUT
> V
IT
0.03 1 mA
Operating junction
T
J
–40 +125 °C
temperature
Shutdown, temperature increasing +155
Thermal shutdown
T
SD
°C
temperature
Reset, temperature decreasing +140
(1) Adjustable devices tested at 0.8V; resistor tolerance is not taken into account.
(2) Dropout is defined as the voltage from the input to V
OUT
when V
OUT
is 2% below nominal.
(3) I
FB
, I
SNS
current flow is out of the device.
4 Submit Documentation Feedback Copyright © 2005–2010, Texas Instruments Incorporated