Datasheet

TPS659110, TPS659112, TPS659113, TPS659116
www.ti.com SWCS049L –JUNE 2010–REVISED MARCH 2014
Table 100. Detailed Revision History (continued)
Version Literature Number Date Notes
D SWCS049D July 2011 See
(5)
.
E SWCS049E July 2011 See
(6)
.
F SWCS049F August 2011 See
(7)
.
(5) TPS65911 Data Manual, SWCS049D - Version D:
(a) Update Absolute Maximum Ratings:
(a) Add VBACKUP
(b) Voltage range on balls HDRST - Replace "VRTCMAX + 0.32 by "7"
(b) Update Recommended Operating Conditions:
(a) Add VCC4 and VBACKUP
(b) Input voltage range on pins or balls - Remove VCC4
(c) Update I/O Pullup And Pulldown Characteristics: Change "HDRST programmable.." to "HDREST, PWRDN programmable.."
(d) Update VRTC LDO: Specify Input voltage range of VCC7
(e) Update VIO SMPS: Add discharge resistance
(f) Update VDD1 SMPS:
(a) Add DC output voltage maximum value
(b) Add discharge resistance
(c) Update VGAIN_SEL test conditions and typ value
(g) Update VDD2 SMPS:
(a) Add DC output voltage maximum value
(b) Add discharge resistance
(c) Update VGAIN_SEL test conditions
(h) Update VDDCtrl SMPS: Add tablenote to Rated output current 6000 mA
(i) Update Switch-ON/-OFF Sequences And Timing:
(a) Update introductory statement
(b) Add note to Figure 4
(c) Align Parameters in Table 4 with Figure 4
(j) Update Power Control Timing: Add note toFigure 5
(k) Update : Add J3 to AGND in Table 3
(l) Update Detailed Description:
(a) Update Table 10: VDD1 and VDD2 voltages
(b) Device POWER ON enable conditions: Add additional device power enable condition
(c) Device SLEEP enable conditions: Replace "... keeping the SLEEP signal floating, or ..." with "... keeping the SLEEP signal in the
active polarity state, or..."
(d) Device reset scenarios: Replace "VCC7 < VBNPR" with " VDD7 < VBNPR and BB < VBNPR"
(e) Update introduction for Table 11
(f) Update Table 11: Remove all values in EEPROM Boot column
(g) Update Table 12:
(a) Remove all values in EEPROM Boot column
(b) Update INT_MSK_REG.VMBHI_MSK description
(m) Update Package Thermal Characteristics: Pin count from 96 to 98
(n) Update Appendix A: Functional Registers:
(a) Update Table 46, Table 47, Table 49, and Table 50: SEL bit description
(b) Update Table 76: Update VMBHI_IT_MSK bit description
(c) Update Table 89: Update GPIO_SEL bit description - Replace LED1 out with PWM out
(6) TPS65911 Data Manual, SWCS049E - Version E: Update .
(7) TPS65911 Data Manual, SWCS049F - Version F:
(a) Add .
(b) Add PCB Layout.
(c) Update Table 76: Update bit 1, VMBHI_IT_MSK description.
(d) Update STATE-MACHINE: Device reset scenarios: Replace "VDD7 < VBNPR" with " VCC7 < VBNPR"
(e) Add Table 2.
Copyright © 2010–2014, Texas Instruments Incorporated Submit Documentation Feedback 113
Product Folder Links: TPS659110 TPS659112 TPS659113 TPS659116