Datasheet

www.ti.com
ABSOLUTE MAXIMUM RATINGS
DISSIPATION RATINGS
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS
TPS65100 , TPS65101
TPS65105
SLVS496C – SEPTEMBER 2003 – REVISED APRIL 2006
over operating free-air temperature range (unless otherwise noted)
(1)
UNIT
Voltages on pin VIN
(2)
-0.3 V to 6 V
Voltages on pin V
O
1, SUP, PG
(2)
-0.3 V to 15.5 V
Voltages on pin EN, MODE, ENR
(2)
-0.3 V to V
I
+ 0.3 V
Voltage on VCOMIN 14 V
Voltage on pin SW
(2)
20 V
Continuous power dissipation See Dissipation Rating Table
Operating junction temperature range -40 ° C to 150 ° C
Storage temperature range -65 ° C to 150 ° C
Lead temperature (soldering, 10 sec) 260 ° C
(1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
T
A
≤ 25 ° C T
A
= 70 °C T
A
= 85 °C
PACKAGE R Θ
JA
POWER RATING POWER RATING POWER RATING
24-Pin TSSOP 30.13 C °/W (PWP soldered) 3.3 W 1.83 W 1.32 W
24-Pin QFN 30 C °/W 3.3 W 1.8 W 1.3 W
MIN TYP MAX UNIT
VIN Input voltage range 2.7 5.8 V
L Inductor
(1)
4.7 µH
T
A
Operating free-air temperature -40 85 °C
T
J
Operating junction temperature -40 125 °C
(1) See the application information section for further information.
V
in
= 3.3 V, EN = VIN, V
O
1 = 10 V, T
A
= -40 °C to 85 °C, typical values are at T
A
= 25 ° C (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY CURRENT
V
i
Input voltage range 2.7 5.8 V
ENR = VCOMIN = GND, V
O
3 = 2 x V
O
1, 0.7 0.9 mA
I
Q
Quiescent current into VIN
Boost converter not switching
V
O
1 = SUP = 10 V, V
O
3 = 2 x V
O
1 1.7 2.7
Charge pump quiescent
I
QCharge
mA
current into SUP
V
O
1 = SUP = 10 V, V
O
3 = 3 x V
O
1 3.9 6
I
QVCOM
VCOM quiescent current into ENR = GND, V
O
1 = SUP = 10 V 750 1300 µA
SUP
I
QEN
LDO controller quiescent ENR = VIN, EN = GND 300 800 µA
current into VIN
I
SD
Shutdown current into VIN EN = ENR = GND 1 10 µA
V
UVLO
Undervoltage lockout VIN falling 2.2 2.4 V
threshold
Thermal shutdown Temperature rising 160 ° C
LOGIC SIGNALS EN, ENR
V
IH
High-level input voltage 1.5 V
V
IL
Low-level input voltage 0.4 V
3
Submit Documentation Feedback