TPS65010EVM-230 U s e r 's G u i d e User's Guide 2003 PMP Portable Power SLVU095A
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use.
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the specified input and output ranges described in the EVM User’s Guide. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power.
Preface Read This First About This Manual This User’s Guide describes the characteristics, operation, and use of the TPS65010EVM-230 evaluation module (EVM), which helps you evaluate and test the various operating modes of the TPS65010. The guide includes setup instructions for the hardware and software, a schematic diagram, a bill of materials (BOM), and PCB layout drawings for the evaluation module.
vi
Contents Read This First ................................................................................................................. v About This Manual...................................................................................................... v How to Use This Manual ............................................................................................ v Related Documentation From Texas Instruments....................................................... v If You Need Assistance ......
viii
Chapter 1 Introduction The Texas Instruments TPS65010EVM-230 is an integrated power and battery management integrated circuit for applications that are powered with one Li-Ion or Li-Polymer cell and require multiple power rails. The TPS65010 contains two highly efficient switching step-down converters, two LDOs, a battery charger, and additional status and I/O pins. You 2 control the device via an I C interface. Topic 1.
Introduction 1.1 Requirements To operate this EVM properly, you must connect and properly configure the following components: ❏ Personal computer A computer with a USB port is required to operate this EVM. The TPS65010 interface software runs on the PC and communicates with the EVM via the PC USB port. You can send commands to the EVM and read the contents of the TPS65010 internal registers through the USB port.
Introduction When installing from a CD: 1) Insert the CD, it should start up automatically. If not, run the Start.bat file on the CD. 2) Install the TPS65010EVM controller program from the main menu first. 3) Install the USB drivers next. (Be sure the EV2300 board is not connected to your computer). Additional manual installation instructions are in the drivers\readme.txt file.
Introduction 1-4
Chapter 2 Setup This chapter describes the jumpers and connectors on the EVM and how to properly connect, setup, and use the TPS65010EVM-230. Topic Page 2.1 Input/Output Connectors 2-2 2.
Setup 2.1 Input/Output Connectors Table 2-1 lists the input/output connectors Table 2-1. Input/Output Connectors Setup Connection Description J1-USB USB charger input/output header can be used as either an input or an output. If R6 is opened, then J1 can be used as an input. An external 5 V can be supplied to the EVM to simulate the USB 5-V bus. If R6 is shorted, J1 may be used as an output. The USB 5-V bus from the PC gets routed through the EV2300 to J5. Shorting R6 connects the USB 5-V bus to J1.
Setup Setup Connection Description J17-LDO1 Input/output connection for LDO1. VINLDO1 can be connected to an external supply or connected to another output voltage on the EVM. The EVM default configuration connects VMAIN to VINLDO1. Remove R25 if a voltage other than VMAIN is used as input to VINLDO1. J18-GND Return connection for LDO1 and LDO2 low dropout linear regulators J19-LDO2 Input/output connection for LDO2.
Setup 2-4
Chapter 3 Board Layout This chapter provides the TPS65010EVM-230 board layout and illustrations. Topic 3.
Board Layout 3.1 Layout Board layout is critical for all switch mode power supplies. Figures 1-5 show the board layout for the TPS65010EVM-230 PWB. The nodes with high switching frequencies and currents are short and are isolated from the noise sensitive feedback circuitry. Careful attention has been given to the routing of high frequency current loops. See the datasheet for specific layout guidelines. Figure 3-1. Assembly Layer.
Board Layout Figure 3-2. Top Layer Routing Figure 3-3.
Board Layout Figure 3-4. Layer 3 Routing Figure 3-5.
Chapter 4 Schematic and Bill of Materials This chapter provides the TPS65010EVM-230 schematic and bill of materials. Topic Page 4.1 Schematic 4-2 4.
Schematic and Bill of Materials 4.1 Schematic Shows the TPS65010EVM-230 schematic Figure 4-1.
Schematic and Bill of Materials 4.2 Bill of Materials Table 4-1. Bill of Materials. Count Ref Des 2 C1, C5 1 C2 2 C3, C8 4 C4, C7, C9, C10 2 C6, C11 1 D1 2 D2, D4 14 J1, J2, J3, J4, J6, J9, J10, J12, J13, J14, J15, J17, J18, J19 1 J11 1 J5 1 J7 2 J8, J16 4 JP1, JP2, JP3, JP4 2 JP5, JP6 1 L1 1 L2 12 R1, R2, R3, R5, R7, R8, R9, R20, R21, R22, R23, R27 2 R10, R16 1 R11 1 R12 3 R13, R25, R26 1 R17 Description Capacitor, Ceramic, 10-uF, 6.
Schematic and Bill of Materials Count Ref Des 1 R18 1 R19 0 R4, R6, R14, R15, R24, R28 2 S1, S2 1 U1 1 6 --- 2 J5 mate 8 N/A N/A N/A N/A N/A 1 4-4 N/A Description Resistor, Chip, 511 k-Ω, 1/16-W, 1% Resistor, Chip, 110k-Ω, 1/16-W, 1% Resistor, Chip, xx-Ω, 1/16-W, 1% Switch, SPST, PB Momentary, Sealed Washable IC, Power & battery management for OMAP systems PCB, 3.7 In x 3.6 In x .062 In Shunt, 100-mil, Black Connector Connector, Female, 0.
