Datasheet

7 List of Materials
List of Materials www.ti.com
Table 2 lists the EVM components as configured according to the schematic shown in Figure 1 .
Table 2. TPS65001EVM Bill of Materials
Count RefDes Value Description Size Part Number MFR
0 C1, C2 open Capacitor, Ceramic, 10V, X5R, 10% 0805 GRM21BR61A106KE19L Murata
2 C3, C10 10 µ F Capacitor, Ceramic, 10V, X5R, 10% 0805 GRM21BR61A106KE19L Murata
2 C4, C11 10 µ F Capacitor, Ceramic, 10V, X5R, 10% 0805 GRM21BR61A106KE19L Murata
1 C5 0.1 µ F Capacitor, Ceramic, 50V, X7R, 10% 0805 GRM21BR71H104KA01L Murata
1 C6 22 pF Capacitor, Ceramic, 50V, C0G, 5% 0603 C1608C0G1H220J TDK
1 C7 0.1 µ F Capacitor, Ceramic, 25V, X7R, 10% 0603 GRM188R71E104KA01D Murata
2 C8, C9 2.2 µ F Capacitor, Ceramic, 16V, X5R, 10% 0603 GRM188R61C225KE15D Murata
2 J1, J4 Header, Male 2-pin, 100mil spacing, (36-pin strip) 0.100 inch × 2 PTC36SAAN Sullins
4 J2, J3, J6, J7 Header, Male 4-pin, 100mil spacing, (36-pin strip) 0.100 inch × 4 PTC36SAAN Sullins
2 J5, J8 Header, Male 3-pin, 100mil spacing, (36-pin strip) 0.100 inch × 3 PTC36SAAN Sullins
7 JP1, JP2, Header, Male 3-pin, 100mil spacing, (36-pin strip) 0.100 inch × 3 PTC36SAAN Sullins
JP3, JP5,
JP6, JP7
1 L1 2.2 µ H Inductor, SMT, 2.0A, 110milliohm 0.118 × 0.118 inch LPS3015-222ML Coilcraft
2 R1, R3 47k Resistor, Chip, 1/10W, 1% 0805 Std Std
1 R10 470k Resistor, Chip, 1/10W, 1% 0805 Std Std
2 R12, R14 0 Resistor, Chip, 1/10W, 1% 0805 Std Std
0 R13, R15 open Resistor, Chip, 1/10W, 1% 0805 Std Std
R2 47k Resistor, Chip, 1/10W, 1% 0805 Std Std
3 R4, R5, R6 475k Resistor, Chip, 1/10W, 1% 0805 Std Std
1 R7 232k Resistor, Chip, 1/10W, 1% 0805 Std Std
1 R8 820k Resistor, Chip, 1/10W, 1% 0805 Std Std
2 R9, R11 180k Resistor, Chip, 1/10W, 1% 0805 Std Std
1 S1 KT11P2JM Switch, SPST, PB Momentary, Sealed Tactile 0.245 × 0.251 inch KT11P2JM C & K
1 U1 TPS65001RUK IC, 2.25MHz Step-Down Converter W/ dual LDO QFN-20 TPS65001RUK TI
and SVS
1 – PCB, 2.6 In × 2 In × 1 In HPA453 Any
9 – Shunt, 100-mil, Black 0.100 929950-00 3M
Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.
2. These assemblies must be clean and free from flux and all contaminants.
Use of no clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ('**') cannot be substituted.
All other components can be substituted with equivalent MFG's components.
14 Using the TPS65001EVM 2.25 MHz Step-Down Converter with Dual LDO SLVU320 – August 2009
Submit Documentation Feedback