Datasheet


   
   
SLVS216B − JUNE 1999 − JUNE 2008
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings (unless otherwise noted)
†‡
Input voltage range, V
I
(IN, OUT, ENABLE, SKIP, COM, CLK, FB, SYNC) −0.3 V to 5.5 V. . . . . . . . . . . . . . . .
Differential input voltage, V
ID
(C1+, C2+ to GND) −0.3 V to (V
O
+ 0.3 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, V
ID
(C1−, C2− to GND) −0.3 V to (V
IN
+ 0.3 V). . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output current 200 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
−55°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10s 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum junction temperature, T
J
150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡
V
ENABLE
, V
SKIP
, V
COM
, V
CLK
and V
SYNC
can exceed V
IN
up to the maximum rated voltage without increasing the leakage current
drawn by these mode select inputs.
DISSIPATION RATING TABLE 1 − FREE-AIR TEMPERATURE (see Figure 3)
PACKAGE
T
A
≤
25
°
C
DERATING FACTOR
T
A
= 70
°
C
T
A
= 85
°
C
PACKAGE
T
A
≤ 25 C
POWER RATING
DERATING FACTOR
ABOVE T
A
= 25°C
T
A
= 70 C
POWER RATING
T
A
= 85 C
POWER RATING
PWP 700 mW 5.6 mW/°C 448 mW 364 mW
DISSIPATION RATING TABLE 2 − CASE TEMPERATURE (see Figure 4)
PACKAGE
T
C
≤
62.5
°
C
DERATING FACTOR
T
C
= 70
°
C
T
C
= 85
°
C
PACKAGE
T
C
≤ 62.5 C
POWER RATING
DERATING FACTOR
ABOVE T
C
= 62.5°C
T
C
= 70 C
POWER RATING
T
C
= 85 C
POWER RATING
PWP 25 W 285.7 mW/°C 22.9 W 18.5 W
Figure 3
1200
800
400
0
25 50 75 100
− Maximum Continuous Dissipation − mW
DISSIPATION DERATING CURVE
§
vs
FREE-AIR TEMPERATURE
125 150
1400
1000
600
200
PWP Package
R
θJA
= 178°C/W
P
D
T
A
− Free-Air Temperature − °C
Figure 4
MAXIMUM CONTINUOUS DISSIPATION
§
vs
CASE TEMPERATURE
T
C
− Case Temperature − °C
15
10
5
0
25 50 75 100
20
25
30
125 150
Measured with the exposed thermal pad
coupled to an infinite heat sink with a
thermally conductive compound (the
thermal conductivity of the compound
is 0.815 W/m ⋅°C). The R
θJC
is 3.5°C/W.
PWP Package
− Maximum Continuous Dissipation − W
P
D
§
Dissipation rating tables and figures are provided for maintenance of junction temperature at or below absolute maximum temperature of 150°C.
It is recommended not to exceed a junction temperature of 125°C.