Datasheet

4 Bill of Materials and Schematic
4.1 Bill of Materials
www.ti.com Bill of Materials and Schematic
This section presents the TPS54917EVM-367 bill of materials and schematic.
Table 5 presents the bill of materials for the TPS54917EVM-367.
Table 5. TPS54917EVM-367 Bill of Materials
RefDes Value Description Size Part Number MFR
C1, C2 22 µ F Capacitor, Ceramic, 6.3V, X5R, 10% 1210 GRM32DR60J22KA01 Murata
C10 330 pF Capacitor, Ceramic, 50V, NPO, 5% 0603 Std Std
C3, C4 100 µ F Capacitor, Ceramic, 6.3V, X5R 1210 C3225X5R0J107M TDK
C5 1200 pF Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std
C6 0.047 µ F Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std
C7 5600 pF Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std
C8 0.047 µ F Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std
C9, C11, C12 0.01 µ F Capacitor, Ceramic, 25V, X5R, 10% 0603 Std Std
C13 Not installed
J1, J4 PTC36SAAN Header, Male 2-pin, 100mil spacing, (36-pin strip) 0.100 inch x 2 PTC36SAAN Sullins
J2, J3 ED1609 Terminal Block, 2-pin, 15-A, 5,1mm 0.40 × 0.35" ED1609 OST
L1 see Note 5 0.35 µ H Inductor, Dual, 11A, 0.264 × 0.295 inch SLC7530-820ML Coilcraft
R1, R2, R8 10.0 k Resistor, Chip, 1/16W, 1% 0603 Std Std
R3 0 Resistor, Chip, 1/16W, 1% 0603 Std Std
R4 10 Resistor, Chip, 1/16W, 1% 0603 Std Std
R5 27.4 k Resistor, Chip, 1/16W, 1% 0603 Std Std
R6 2.32 k Resistor, Chip, 1/16W, 1% 0603 Std Std
R7 681 Resistor, Chip, 1/16W, 1% 0603 Std Std
TP1–TP4 5000 Test Point, Red, Thru Hole Color Keyed 0.100 × 0.100 inch 5000 Keystone
TP5, TP6 5006 Test Point, Black, Thru Hole Compact Style 0.125 × 0.125 inch 5006 Keystone
TP7 5001 Test Point, Black, Thru Hole Color Keyed 0.100 × 0.100 inch 5001 Keystone
U1 TPS54917RUV IC, 3-V TO 4-V INPUT, 9-A, Small synchronous-buck RUV-34 TPS54917RUV TI
– Shunt, 100-mil, Black 0.100 929950-00 3M
PCB, 3.0" × 3.0" × 0.062" HPA367 Any
Notes: 1. These assemblies are ESD sensitive, ESD precautions shall be observed.
2. These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Ref designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFR's
components.
5. L1 is used in series and the value is 0.35 µ H.
SLVU278 – December 2008 TPS54917EVM-367 9-A, SWIFT™ Regulator Evaluation Module 13
Submit Documentation Feedback