Datasheet
Table Of Contents
- FEATURES
- APPLICATIONS
- DESCRIPTION
- ABSOLUTE MAXIMUM RATINGS
- THERMAL INFORMATION
- ELECTRICAL CHARACTERISTICS
- DEVICE INFORMATION
- TYPICAL CHARACTERISTICS
- OVERVIEW
- DETAILED DESCRIPTION
- Fixed Frequency PWM Control
- Slope Compensation Output Current
- Pulse Skip Eco-Mode
- Low Dropout Operation and Bootstrap Voltage (BOOT)
- Error Amplifier
- Voltage Reference
- Adjusting the Output Voltage
- Enable and Adjusting Undervoltage Lockout
- Slow Start/Tracking Pin (SS/TR)
- Overload Recovery Circuit
- Sequencing
- Constant Switching Frequency and Timing Resistor (RT/CLK Pin)
- Overcurrent Protection and Frequency Shift
- Selecting the Switching Frequency
- How to Interface to RT/CLK Pin
- Power Good (PWRGD Pin)
- Overvoltage Transient Protection
- Thermal Shutdown
- Small Signal Model for Loop Response
- Simple Small Signal Model for Peak Current Mode Control
- Small Signal Model for Frequency Compensation
- APPLICATION INFORMATION
- Design Guide — Step-By-Step Design Procedure
- Selecting the Switching Frequency
- Output Inductor Selection (LO)
- Output Capacitor
- Catch Diode
- Input Capacitor
- Slow Start Capacitor
- Bootstrap Capacitor Selection
- Under Voltage Lock Out Set Point
- Output Voltage and Feedback Resistors Selection
- Compensation
- Discontinuous Mode and Eco Mode Boundary
- APPLICATION CURVES
- Power Dissipation Estimate
- Layout
- Revision History

( )
( )
( )
L OUT
SW max skip
ON IN L
I Rdc V Vd
1
t V I Rhs Vd
æ ö
´ + +
æ ö
= ´
ç ÷
ç ÷
ç ÷
- ´ +
è ø
è ø
f
( )
( )
L OUTSC
SW hift
ON IN L
(I Rdc V Vd)
div
t V I x Rhs Vd
æ ö
´ + +
= ´
ç ÷
ç ÷
- +
è ø
f
f
Skip
Shift
10
20 30
40 50
60
2500
2000
1500
1000
500
0
f -SwitchingFrequency-kHz
s
V -InputVoltage-V
I
V =3.3V
O
TPS54060
SLVS919A –JANUARY 2009–REVISED JULY 2010
www.ti.com
DETAILED DESCRIPTION (continued)
Selecting the Switching Frequency
The switching frequency that is selected should be the lower value of the two equations, Equation 12 and
Equation 13. Equation 12 is the maximum switching frequency limitation set by the minimum controllable on time.
Setting the switching frequency above this value will cause the regulator to skip switching pulses.
Equation 13 is the maximum switching frequency limit set by the frequency shift protection. To have adequate
output short circuit protection at high input voltages, the switching frequency should be set to be less than the
fsw(maxshift) frequency. In Equation 13, to calculate the maximum switching frequency one must take into
account that the output voltage decreases from the nominal voltage to 0 volts, the fdiv integer increases from 1 to
8 corresponding to the frequency shift.
In Figure 41, the solid line illustrates a typical safe operating area regarding frequency shift and assumes the
output voltage is zero volts, and the resistance of the inductor is 0.130Ω, FET on resistance of 0.2Ω and the
diode voltage drop is 0.5V. The dashed line is the maximum switching frequency to avoid pulse skipping. Enter
these equations in a spreadsheet or other software or use the SwitcherPro design software to determine the
switching frequency.
(12)
(13)
I
L
inductor current
Rdc inductor resistance
V
IN
maximum input voltage
V
OUT
output voltage
V
OUTSC
output voltage during short
Vd diode voltage drop
R
DS(on)
switch on resistance
t
ON
controllable on time
ƒ
DIV
frequency divide equals (1, 2, 4, or 8)
Figure 41. Maximum Switching Frequency vs. Input Voltage
22 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): TPS54060