Datasheet
8 List of Materials
List of Materials
www.ti.com
Table 8. TPS2348 List of Materials
(1) (2) (3) (4) (5) (6) (7) (8) (9)
COUNT REF DES DESCRIPTION PART NUMBER MFR
3 C1, C2, C3 Capacitor, ceramic, 25 V, X7R, 20%, 0.1 µ F, 0805 Std. Std.
1 C11 Capacitor, aluminum, SM, 10 V, ± 20%, 150 µ F, EEV-FK1A151P Panasonic
case D
1 C12 Capacitor, ceramic, 10 V, X7R, 10%, 0.022 µ F, Std. Std.
0805
2 C13, C17 Capacitor, ceramic, 10 V, X7R, 10%, 0.047 µ F, Std. Std.
0805
1 C14 Capacitor, ceramic, 10 V, X7R, 10%, 0.1 µ F, 0805 Std. Std.
0 C15 Capacitor, ceramic, 10 V, X7R, 10%, 0805 Std. Std.
1 C16 Capacitor, ceramic, 10 V, X7R, 10%, 0.01 µ F, 0805 Std. Std.
2 C4, C5 Capacitor, ceramic, 25 V, X7R, 20%, 1 µ F, 0805 Std. Std.
1 C6 Capacitor, aluminum, SM, 25 V, ± 20%, 47 µ F, EEV-FK1E470P Panasonic
Case D
4 C7, C8, C9, C10 Capacitor, aluminum, SM, 25 V, ± 20%, 220 µ F, EEV-FK1E221P Panasonic
Case F
1 D1 Diode, TVS, V(RWM) = 13.6 V, 600 W pk., SMB P6SMB16A "ON Semior
Vishayor Littelfuse"
1 D2 Diode, Zener, 4.3 V, 500 mW max., SOD-123 BZT52C4V3 Diodes
1 D3 Diode, Schottky, 1 A, 20 V, SMA B120 Diodes
2 D4, D5 Diode, LED, red/green, 1210, 45/35 mcd @ 20 mA, LTST- Lite-On
0.126 x 0.106in. C155KGJRKT
6 J1, J2, J3, J4, J5, Jack, banana, non-ins., PC mount, TH 3267 Pomona
J6
10 J7, J8, J9, J10, Header, 2 pin, 100-mil spacing, 0.100 in. x 2 PEC36SAAN Sullins
J11, J12, J13, J14,
J15, J16
1 Q1 Transistor, NFET, 30 V, 100A, R
DS(on)
< 5 mohm, "BSC016N03LSG# Infineon
TDSON-8 #or
BSC022N03SG"
1 Q2 Transistor, NFET, 30 V, R
DS(on)
< 20 mohm, "BSC057N03LSG# Infineon
TDSON-8 #or
BSC050N03LSGor
BSC042N03LSGor
BSC022N03SGor
BSC016N03LSG"
(1)
These assemblies are ESD sensitive, ESD precautions shall be observed.
(2)
These assemblies must be clean and free from flux and all contaminants. Use of no clean flux is not acceptable.
(3)
These assemblies must comply with workmanship standards IPC-A-610 Class 2.
(4)
"TH" package designation indicates "thru-hole" (leaded ) component.
(5)
Part number information is for reference only to further illustrate component characteristics; substitution of other mfgrs' part of
equal or better specification is permissible. Substitution NOT allowed on part numbers marked with double asterisk (**).
(6)
Double pound sign ('##') after part number indicates preferred device. Acceptable substitutes are listed afterwards, in
decreasing order of preference.
(7)
If banana jacks (J1 - J6) are supplied with solder lugs, dispose of lugs prior to installation on PCB. Solder lugs are NOT to be
installed on assembly.
(8)
Spacers to be installed at each of the thru-holes at the four corners of the PCB assembly, using nylon screws.
(9)
Shunts installed in accordance with manufacturing test procedure during test.
14 TPS2458 ATCA™ AdvancedMC™ Controller SLUU348A – February 2009 – Revised August 2009
Submit Documentation Feedback