TPIC74100EVM User's Guide User's Guide Literature Number: SLIU002 September 2008
SLIU002 – September 2008 Submit Documentation Feedback
Contents 1 2 3 4 Introduction......................................................................................................................... 5 Setup .................................................................................................................................. 5 2.1 Input/Output Connector Description .................................................................................... 5 2.2 Setup................................................................................
www.ti.com List of Figures 1 2 3 4 5 6 7 8 9 10 Slew Rate Jumper Settings................................................................................................. 5 Low Power Mode Jumper Settings ........................................................................................ 6 Enable Jumper Settings..................................................................................................... 6 5Vg Regulated Output Jumper Settings ....................................................
User's Guide SLIU002 – September 2008 TPIC74100EVM User's Guide 1 Introduction The Texas Instruments TPIC74100EVM evaluation module (EVM) helps designers evaluate the operation and performance of the TPIC74100 Switch Mode Power Supply – Buck Regulator. The EVM contains one DC/DC converter (See Table 1). Table 1.
Setup www.ti.com JP3 – LPM is the jumper used to enable Low Power Mode. The jumper allows LPM to be enabled or disabled. The device will operate in Normal mode when LPM is disabled. 0 0 1 1 LPM LPM disabled enabled Figure 2. Low Power Mode Jumper Settings JP4 – Enable is the jumper used to enable the converter. The converter is enabled when the Enable is high and disabled when low. The jumper placement allows the converter to be enabled or disabled.
Board Layout www.ti.com 2.3 Operation For proper operation of the TPIC74100, JP1, JP2, JP3, JP4, JP5, and JP6 should be properly configured. The recommended setting, using shorting blocks: JP1 and JP2 to Fast JP3 to Enabled JP4 to Enabled JP5 to Enabled, if 5Vg is used JP6 to Shorted In this configuration, the device powers up when power is applied. JP1, JP2 SCR0, SCR1 select how switch pin slew rate is set: slow, medium-slow, medium-fast, or fast.
Board Layout www.ti.com Figure 7. Bottom Assembly Layer Figure 8.
Board Layout www.ti.com Figure 9.
GND C5 JP6 + 1 2 C6 1 VBAT GND 2 R5 R2 GND GND AIN VDRIVER L2 D1 GND GND VOUT VOUT C1 GND L1 GND 1 C7 1 JP1 + C8 GND 2 SCR1 1 TPIC74100EVM User's Guide 2 10 D2 C2 GND 5Vg JP2 VLOGIC 1 C9 AIN GND VDRIVER SCR1 GND 10 9 8 7 6 5 4 3 2 1 SCR0 GND 1 Ain 5Vg Vout L2 PGND L1 Vdriver Cboot1 Cboot2 SCR1 GND CLP RESET Aout REST Rmod GND Vlogic ENABLE 5Vg_ENABLE SCR0 TPIC74100PWP JP3 VLOGIC PAD GND RESET 12 LPM AOUT 13 11 C4 RES
Schematic www.ti.com Table 2. TPIC74100EVM Bill of Materials COUNT REF DES DESCRIPTION SIZE MFR PART NO. 2 C1, C2 Capacitor, ceramic, 4.
EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
