TPA711 MSOP Audio Power Amplifier Evaluation Module User’s Guide 2001 Mixed-Signal Products SLOU027B
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete.
Preface Related Documentation From Texas Instruments J J TI Plug-N-Play Audio Amplifier Evaluation Platform (literature number SLOU011) provides detailed information on the evaluation platform and its use with TI audio evaluation modules. TPA711 700-mW Low-Voltage Audio Power Amplifier (literature number SLOS230) This is the data sheet for the TPA711 audio amplifier integrated circuit. FCC Warning This equipment is intended for use in a laboratory test environment only.
iv
Running Title—Attribute Reference Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.
Running Title—Attribute Reference Figures 1–1 2–1 2–2 3–1 3–2 3–3 3–4 3–5 3–6 3–7 3–8 3–9 The TI TPA711 MSOP Audio Amplifier Evaluation Module . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Quick Start Platform Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Quick Start Module Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction This chapter provides an overview of the Texas Instruments (TI) TPA711 MSOP audio amplifier evaluation module (SLOP214). It includes a list of EVM features, a brief description of the module illustrated with a pictorial diagram, and a list of EVM specifications. Topic Page 1.1 Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 1.2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Highlights 1.1 Feature Highlights The TI TPA711 MSOP audio amplifier evaluation module and the TI plug-n-play audio amplifier evaluation platform include the following features: - - TPA711 Low-Voltage Audio Power Amplifier Evaluation Module J J J J J J - 1-2 3.
Description 1.2 Description The TPA711 MSOP audio power amplifier evaluation module is a complete, low-power single-channel audio power amplifier. It consists of the TI TPA711 700-mW low-voltage audio power amplifier IC in a very small MSOP package, along with a small number of other parts mounted on a circuit board that is approximately one and a quarter inches square (Figure 1–1). Figure 1–1.
1-4 Introduction
Chapter 2 Quick Start The steps in this chapter can be followed to quickly prepare the TPA711 MSOP audio amplifier EVM for use. Using the TPA711 MSOP EVM with the TI plug-n-play audio amplifier evaluation platform is a quick and easy way to connect power, signal and control inputs, and signal outputs to the EVM, using standard connectors.
Precautions 2.1 Precautions Power Supply Input Polarity and Maximum Voltage Always ensure that the polarity and voltage of the external power connected to VCC power input connector J1, J2, and/or VDD power input connector J6 are correct. Overvoltage or reverse-polarity power applied to these terminals can open onboard soldered-in fuses and cause other damage to the platform, installed evaluation modules, and/or the power source.
Quick Start List for Platform 2.2 Quick Start List for Platform - Follow these steps when using the TPA711 MSOP EVM with the TI plug-n-play audio amplifier evaluation platform (see the platform user’s guide, SLOU011, for additional details). Numbered callouts for selected steps are shown in Figure 2–1 and details appear in Chapter 3. Platform preparations 1) Ensure that all external power sources are set to OFF and that the platform power switch S1 is set to OFF.
Quick Start List for Stand-Alone 2.3 Quick Start List for Stand-Alone Follow these steps to use the TPA711 MSOP EVM stand-alone or when connecting it into existing circuits or equipment. Connections to the TPA711 MSOP module header pins can be made via individual sockets, wire-wrapping, or soldering to the pins, either on the top or the bottom of the module circuit board. Numbered callouts for selected steps are shown in Figure 2–2 and details appear in Chapter 3. Figure 2–2.
Chapter 3 Details This chapter provides details on the TPA711 IC, the evaluation module, the steps in the Quick-Start List, additional application information, and a parts list for the TPA711 MSOP evaluation module. Topic Page 3.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2 3.2 The TPA711 MSOP Audio Power Amplifier Evaluation Module . . . . 3–3 3.3 Using The TPA711 MSOP EVM With The Plug-N-Play Evaluation Platform . . . . . . .
Precautions 3.1 Precautions Power Supply Input Polarity and Maximum Voltage Always ensure that the polarity and voltage of the external power connected to VCC power input connector J1, J2, and/or VDD power input connector J6 are correct. Overvoltage or reverse-polarity power applied to these terminals can open onboard soldered-in fuses and cause other damage to the platform, installed evaluation modules, and/or the power source.
The TPA711 MSOP Audio Power Amplifier Evaluation Module 3.2 The TPA711 MSOP Audio Power Amplifier Evaluation Module The TPA711 MSOP audio power amplifier evaluation module is powered by a TPA711 700-mW low-power audio amplifier IC, includes a shutdown control signal input with on-board switch, and can be operated in either the BTL or single-ended output mode. The module can be used with the TI plug-n-play audio amplifier evaluation platform (Figure 3 –1) or wired directly into circuits or equipment.
The TPA711 MSOP Audio Power Amplifier Evaluation Module 3.2.1 TPA711 Audio Amplifier IC The TPA711 audio amplifier IC is a CMOS device intended primarily for bridge-tied load (BTL) operation in battery-powered applications. It is supplied in a very small surface-mount package and has been designed to operate from low supply voltages (between approximately 2.5 V and 5.5 V) and deliver up to approximately 700 mW into an 8-Ω, BTL (Figure 3 – 4).
The TPA711 MSOP Audio Power Amplifier Evaluation Module 3.2.3 SIngle-Ended Operation For single-ended operation, the module SE/BTL control input pin must be held high. The speaker (or headphone) load is connected to the module OUT+ output pin through a coupling capacitor, and to platform/system ground.
Using The TPA711 MSOP EVM With the Plug-N-Play Evaluation Platform 3.3 Using The TPA711 MSOP EVM With the Plug-N-Play Evaluation Platform The TPA711 MSOP audio amplifier evaluation module was designed to be used with the TI plug-n-play audio amplifier evaluation platform. It simply plugs into socket U3 or U4. The following paragraphs provide additional details for using the TPA711 MSOP EVM with the platform. 3.3.
Using The TPA711 MSOP EVM With the Plug-N-Play Evaluation Platform 3.3.2 Signal Routing Signal flow on the platform is controlled by two signal routing switches, as shown in Figure 3 – 5. Figure 3–5. Platform Signal Routing and Outputs Off R Audio Input U1 Signal Conditioning U3 TPA711 Amplifier EVM R U4 TPA711 Amplifier EVM L + R – S2 L On – J7, J8, J9 Speaker Outputs L + U2 – U4 R U5 Stereo Headphone Amplifier R S3 + – J10 Headphone Output – GND L L + U5 3.3.2.
Using The TPA711 MSOP EVM With the Plug-N-Play Evaluation Platform 3.3.3 Mute/Mode The TPA711 MSOP EVM is equipped with a mute (shutdown) control input pin. When this input is tied to VDD, the TPA711 amplifier IC on the module shuts down and assumes an ultra-low power mode. When the EVM control input is tied to GND or allowed to float, amplifier operation resumes.
Using The TPA711 MSOP EVM With the Plug-N-Play Evaluation Platform 3.3.3.2 Mute/Mode Select (JP6) A 3-pin jumper header (JP6) on the platform, functioning as a SPDT switch, routes the control signal from the headphone jack to either the mute control input pin or the mode control input pin of the evaluation module. J J 3.3.3.3 To mute the TPA711 MSOP amplifier module using the control signal from the platform headphone jack, jumper JP6 to MUTE.
Power Requirements 3.3.4 Power Requirements The TPA711 MSOP audio power amplifier evaluation module can operate from any voltage between approximately 2.5 V and 5.5 V; however, the TPA711 amplifier IC on the module is characterized for operation at 3.3 V and 5 V. For best performance (highest output power with lowest distortion), the module should be operated at approximately 5 V, unless there is a specific reason for operating it from a lower voltage.
Inputs and Outputs 3.3.5 Inputs and Outputs The TI plug-n-play audio amplifier evaluation platform is equipped with several standard conectors for audio inputs and outputs. 3.3.5.1 Inputs In most cases, audio signals enter the platform through either a pair of RCA phono jacks (J3 and J5) or a miniature (1/8″) stereo phone jack (J4). Certain signal conditioning and amplifier EVMs, however, may have additional signal input connectors mounted on the module circuit board.
Using The TPA711 MSOP EVM Stand-Alone 3.4 Using The TPA711 MSOP EVM Stand-Alone Using the TPA711 MSOP audio power amplifier evaluation module stand-alone is much the same as using it with the platform. The same 2.5-V to 5.5-V power supply range and the isolated OUT+ and OUT– lines for BTL operation requirement exists. Note that the mute signal applied to the EVM shutdown pins must be able to supply enough current to overcome the pulldown resistors on the modules (20 kΩ || 20 kΩ for two EVMs). 3.4.
Using The TPA711 MSOP EVM Stand-Alone 3.4.2 TPA711 MSOP EVM Connected for Single-Ended Output Figure 3–9.
TPA711 MSOP Audio Power Amplifier Evaluation Module Parts List 3.5 TPA711 MSOP Audio Power Amplifier Evaluation Module Parts List Table 3–1. TPA711 MSOP EVM Parts List Ref. Description Size EVM Qty. Manufacturer/ Part Number A 1 Panasonic ECS-TOJY106R Murata GRM39-Y5V105Z10PT Vendor Number C5 Capacitor, 10 µF, 6.
