Datasheet


SLOS386A − NOVEMBER 2001 − REVISED APRIL 2007
4
www.ti.com
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
†
Supply voltage, V
DD
6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, V
I
−0.3 V to V
DD
+0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation internally limited (see Dissipation Rating Table). . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, T
A
−40°C to 85°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating junction temperature range, T
J
−40°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, T
stg
−65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrostatic discharge HBM:2 kV typical, CDM:200 V typical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
T
A
≤ 25°C DERATING FACTOR T
A
= 70°C T
A
= 85°C
PWP 2.7 W
‡
21.8 mW/°C 1.7 W 1.4 W
‡
See the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report
(literature number SLMA002), for more information on the PowerPAD package. The thermal data was
measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended
Board for PowerPAD on page 33 of the before mentioned document.
recommended operating conditions
MIN MAX UNIT
Supply voltage, V
DD
4.5 5.5 V
High-level input voltage, V
IH
SHUTDOWN 2 V
Low-level input voltage, V
IL
SHUTDOWN 0.8 V
Operating free-air temperature, T
A
−40 85 °C
electrical characteristics at specified free-air temperature, V
DD
= 5 V, T
A
= 25°C (unless otherwise
noted)
PARAMETER TEST CONDITIONS
MIN TYP MAX UNIT
|V
OO
| Output offset voltage (measured differentially) V
I
= 0, A
v
= −2 V/V 25 mV
PSRR Power supply rejection ratio V
DD
= 4.5 V to 5.5 V 77 dB
|I
IH
| High-level input current
V
DD
= 5.5 V,
V
I
= V
DD
1 µA
|I
IL
| Low-level input current
V
DD
= 5.5 V,
V
I
= 0 V
1 µA
I
DD
Supply current SHUTDOWN = 2 V 6 10 mA
I
DD(SD)
Supply current, shutdown mode SHUTDOWN = 0.8 V 150 300 µA