Datasheet
TPA3116D2
TPA3118D2
TPA3130D2
www.ti.com
SLOS708C –APRIL 2012–REVISED NOVEMBER 2013
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
(1)
VALUE UNIT
Supply voltage, V
CC
PV
CC
, AV
CC
–0.3 to 30 V
INPL, INNL, INPR, INNR –0.3 to 6.3 V
Input voltage, V
I
PLIMIT, GAIN / SLV, SYNC –0.3 to GVDD+0.3 V
AM0, AM1, AM2, MUTE, SDZ, MODSEL –0.3 to PVCC+0.3 V
Slew rate, maximum
(2)
AM0, AM1, AM2, MUTE, SDZ, MODSEL 10 V/msec
Operating free-air temperature, T
A
–40 to 85 °C
Operating junction temperature range, T
J
–40 to 150 °C
Storage temperature range, T
stg
–40 to 125 °C
Electrostatic discharge: Human body model, ESD ±2 kV
Electrostatic discharge: Charged device model, ESD ±500 V
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) 100 kΩ series resistor is needed if maximum slew rate is exceeded.
THERMAL INFORMATION
TPA3130D2 TPA3118D2 TPA3116D2
DAP DAP DAD
THERMAL METRIC
(1)
UNITS
1 Layer PCB
(2)
2 Layer PCB
(3)
Heatsink
(4)
32 PINS 32 PINS 32 PINS
θ
JA
Junction-to-ambient thermal resistance 36 22 14
ψ
JT
Junction-to-top characterization parameter 0.4 0.3 1.2 °C/W
ψ
JB
Junction-to-board characterization parameter 5.9 4.8 5.7
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) For the PCB layout please see the TPA3130D2EVM user guide.
(3) For the PCB layout please see the TPA3118D2EVM user guide.
(4) The heat sink drawing used for the thermal model data are shown in the application section, size: 14mm wide, 50mm long, 25mm high.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN NOM MAX UNIT
V
CC
Supply voltage PV
CC
, AV
CC
4.5 26 V
High-level input
V
IH
AM0, AM1, AM2, MUTE, SDZ, SYNC, MODSEL 2 V
voltage
Low-level input
V
IL
AM0, AM1, AM2, MUTE, SDZ, SYNC, MODSEL 0.8 V
voltage
Low-level output
V
OL
FAULTZ, R
PULL-UP
= 100 kΩ, PV
CC
= 26 V 0.8 V
voltage
High-level input
I
IH
AM0, AM1, AM2, MUTE, SDZ, MODSEL (V
I
= 2 V, V
CC
= 18 V) 50 µA
current
TPA3116D2, TPA3118D2 3.2 4
R
L
(BTL) Output filter: L = 10 µH, C = 680 nF
TPA3130D2 5.6 8
Minimum load
Ω
Impedance
TPA3116D2, TPA3118D2 1.6
R
L
(PBTL) Output filter: L = 10 µH, C = 1 µF
TPA3130D2 3.2 4
Output-filter
L
o
Minimum output filter inductance under short-circuit condition 1 µH
Inductance
Copyright © 2012–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: TPA3116D2 TPA3118D2 TPA3130D2