Datasheet
TMS320LF2407A,TMS320LF2406A,TMS320LF2403A,TMS320LF2402A
TMS320LC2406A,TMS320LC2404A,TMS320LC2403A,TMS320LC2402A
DSP CONTROLLERS
SPRS145L − JULY 2000 − REVISED SEPTEMBER 2007
19
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
pin functions (continued)
Table 2. LF240xA and LC240xA Pin List and Package Options
†‡
(Continued)
PIN NAME
LF2407A
(144-PGE)
2406A
(100-PZ)
LC2404A
(100-PZ)
2403A,
LC2402A
(64-PAG)
and
2402A
(64-PG)
DESCRIPTION
ADDRESS, DATA, AND MEMORY CONTROL SIGNALS (CONTINUED)
A12 43 Bit 12 of the 16-bit address bus
A13 39 Bit 13 of the 16-bit address bus
A14 34 Bit 14 of the 16-bit address bus
A15 31 Bit 15 of the 16-bit address bus
D0 127 Bit 0 of 16-bit data bus (↑)
D1 130 Bit 1 of 16-bit data bus (↑)
D2 132 Bit 2 of 16-bit data bus (↑)
D3 134 Bit 3 of 16-bit data bus (↑)
D4 136 Bit 4 of 16-bit data bus (↑)
D5 138 Bit 5 of 16-bit data bus (↑)
D6 143 Bit 6 of 16-bit data bus (↑)
D7 5 Bit 7 of 16-bit data bus (↑)
D8 9 Bit 8 of 16-bit data bus (↑)
D9 13 Bit 9 of 16-bit data bus (↑)
D10 15 Bit 10 of 16-bit data bus (↑)
D11 17 Bit 11 of 16-bit data bus (↑)
D12 20 Bit 12 of 16-bit data bus (↑)
D13 22 Bit 13 of 16-bit data bus (↑)
D14 24 Bit 14 of 16-bit data bus (↑)
D15 27 Bit 15 of 16-bit data bus (↑)
POWER SUPPLY
29 20 20 6
V
#
50 35 35 27
Core supply 3 3 V Digital logic supply voltage
V
DD
#
86 59 59 56
Core supply +3.3 V. Digital logic supply voltage.
129 91 91
4 4 4 10
42 30 30 35
V
#
67 47 47 52
I/O buffer suppl
y
+3.3 V. Di
g
ital lo
g
ic and buffer suppl
y
V
DDO
#
77 54 54
I/O buffer supply +3
.
3 V
.
Digital logic and buffer supply
voltage.
95 64 64
141 98 98
†
Bold, italicized pin names indicate pin function after reset.
‡
GPIO − General-purpose input/output pin. All GPIOs come up as input after reset.
§
It is highly recommended that V
CCA
be isolated from the digital supply voltage (and V
SSA
from digital ground) to maintain the specified accuracy
and improve the noise immunity of the ADC.
¶
Only when all of the following conditions are met: EMU1/OFF is low, TRST is low, and EMU0 is high
#
No power supply pin (V
DD
, V
DDO
, V
CCA
, V
SS
, or V
SSO
) should be left unconnected. All power supply pins must be connected appropriately for
proper device operation.
LEGEND: ↑ − Internal pullup ↓ − Internal pulldown (Typical active pullup/pulldown value is ±16 µA.)