Datasheet

TMS320LF2407A,TMS320LF2406A,TMS320LF2403A,TMS320LF2402A
TMS320LC2406A,TMS320LC2404A,TMS320LC2403A,TMS320LC2402A
DSP CONTROLLERS
SPRS145L − JULY 2000 − REVISED SEPTEMBER 2007
12
POST OFFICE BOX 1443 • HOUSTON, TEXAS 77251−1443
pin functions (continued)
Table 2. LF240xA and LC240xA Pin List and Package Options
†‡
(Continued)
PIN NAME
LF2407A
(144-PGE)
2406A
(100-PZ)
LC2404A
(100-PZ)
2403A,
LC2402A
(64-PAG)
and
2402A
(64-PG)
DESCRIPTION
EVENT MANAGER B (EVB) (CONTINUED)
T3PWM/T3CMP/IOPF2 8 7 7 Timer 3 compare output (EVB) or GPIO (↑)
T4PWM/T4CMP/IOPF3 6 5 5 Timer 4 compare output (EVB) or GPIO (↑)
TDIRB/IOPF4 2 2 2
Counting direction for general-purpose (GP) timer
(EVB) or GPIO. If TDIRB = 1, upward counting is
selected. If TDIRB = 0, downward counting is
selected. (↑)
TCLKINB/IOPF5 126 89 89
External clock input for GP timer (EVB) or GPIO.
Note that the timer can also use the internal
device clock. (↑)
ANALOG-TO-DIGITAL CONVERTER (ADC)
ADCIN00 112 79 79 18 Analog input #0 to the ADC
ADCIN01 110 77 77 17 Analog input #1 to the ADC
ADCIN02 107 74 74 16 Analog input #2 to the ADC
ADCIN03 105 72 72 15 Analog input #3 to the ADC
ADCIN04 103 70 70 14 Analog input #4 to the ADC
ADCIN05 102 69 69 13 Analog input #5 to the ADC
ADCIN06 100 67 67 12 Analog input #6 to the ADC
ADCIN07 99 66 66 11 Analog input #7 to the ADC
ADCIN08 113 80 80 Analog input #8 to the ADC
ADCIN09 111 78 78 Analog input #9 to the ADC
ADCIN10 109 76 76 Analog input #10 to the ADC
ADCIN11 108 75 75 Analog input #11 to the ADC
ADCIN12 106 73 73 Analog input #12 to the ADC
ADCIN13 104 71 71 Analog input #13 to the ADC
ADCIN14 101 68 68 Analog input #14 to the ADC
ADCIN15 98 65 65 Analog input #15 to the ADC
V
REFHI
115 82 82 20 ADC analog high-voltage reference input
V
REFLO
114 81 81 19 ADC analog low-voltage reference input
V
CCA
116 83 83 21 Analog supply voltage for ADC (3.3 V)
§
V
SSA
117 84 84 22 Analog ground reference for ADC
†
Bold, italicized pin names indicate pin function after reset.
‡
GPIO − General-purpose input/output pin. All GPIOs come up as input after reset.
§
It is highly recommended that V
CCA
be isolated from the digital supply voltage (and V
SSA
from digital ground) to maintain the specified accuracy
and improve the noise immunity of the ADC.
¶
Only when all of the following conditions are met: EMU1/OFF is low, TRST is low, and EMU0 is high
#
No power supply pin (V
DD
, V
DDO
, V
CCA
, V
SS
, or V
SSO
) should be left unconnected. All power supply pins must be connected appropriately for
proper device operation.
LEGEND: ↑ − Internal pullup ↓ − Internal pulldown (Typical active pullup/pulldown value is ±16 µA.)