Datasheet
Table Of Contents
- 1 Digital Media System-on-Chip (DMSoC)
- Table of Contents
- 2 Revision History
- 3 Device Overview
- 3.1 Device Characteristics
- 3.2 Device Compatibility
- 3.3 ARM Subsystem
- 3.3.1 ARM926EJ-S RISC CPU
- 3.3.2 CP15
- 3.3.3 MMU
- 3.3.4 Caches and Write Buffer
- 3.3.5 Tightly Coupled Memory (TCM)
- 3.3.6 Advanced High-Performance Bus (AHB)
- 3.3.7 Embedded Trace Macrocell (ETM) and Embedded Trace Buffer (ETB)
- 3.3.8 ARM Memory Mapping
- 3.3.9 Peripherals
- 3.3.10 PLL Controller (PLLC)
- 3.3.11 Power and Sleep Controller (PSC)
- 3.3.12 ARM Interrupt Controller (AINTC)
- 3.3.13 System Module
- 3.3.14 Power Management
- 3.4 DSP Subsystem
- 3.5 Memory Map Summary
- 3.6 Pin Assignments
- 3.7 Terminal Functions
- 3.8 Device Support
- 3.9 Documentation Support
- 3.10 Community Resources
- 4 Device Configurations
- 4.1 System Module Registers
- 4.2 Power Considerations
- 4.3 Clock Considerations
- 4.4 Boot Sequence
- 4.5 Configurations At Reset
- 4.6 Configurations After Reset
- 4.7 Multiplexed Pin Configurations
- 4.7.1 Pin Muxing Selection At Reset
- 4.7.2 Pin Muxing Selection After Reset
- 4.7.3 Pin Multiplexing Details
- 4.7.3.1 PCI, HPI, EMIFA, and ATA Pin Muxing
- 4.7.3.2 PWM Signal Muxing
- 4.7.3.3 TSIF0 Input Signal Muxing (Serial/Parallel)
- 4.7.3.4 TSIF0 Output Signal Muxing (Serial/Parallel)
- 4.7.3.5 TSIF1 Input Signal Muxing (Serial Only)
- 4.7.3.6 TSIF1 Output Signal Muxing (Serial Only)
- 4.7.3.7 CRGEN Signal Muxing
- 4.7.3.8 UART0 Pin Muxing
- 4.7.3.9 UART1 Pin Muxing
- 4.7.3.10 UART2 Pin Muxing
- 4.7.3.11 ARM/DSP Communications Interrupts
- 4.7.3.12 Emulation Control
- 4.8 Debugging Considerations
- 5 System Interconnect
- 6 Device Operating Conditions
- 7 Peripheral Information and Electrical Specifications
- 7.1 Parameter Information
- 7.2 Recommended Clock and Control Signal Transition Behavior
- 7.3 Power Supplies
- 7.4 External Clock Input From DEV_MXI/DEV_CLKIN and AUX_MXI/AUX_CLKIN Pins
- 7.5 Clock PLLs
- 7.6 Enhanced Direct Memory Access (EDMA3) Controller
- 7.7 Reset
- 7.8 Interrupts
- 7.9 External Memory Interface (EMIF)
- 7.10 DDR2 Memory Controller
- 7.10.1 DDR2 Memory Controller Electrical Data/Timing
- 7.10.2 DDR2 Interface
- 7.10.2.1 DDR2 Interface Schematic
- 7.10.2.2 Compatible JEDEC DDR2 Devices
- 7.10.2.3 PCB Stackup
- 7.10.2.4 Placement
- 7.10.2.5 DDR2 Keep Out Region
- 7.10.2.6 Bulk Bypass Capacitors
- 7.10.2.7 High-Speed Bypass Capacitors
- 7.10.2.8 Net Classes
- 7.10.2.9 DDR2 Signal Termination
- 7.10.2.10 VREF Routing
- 7.10.2.11 DDR2 CK and ADDR_CTRL Routing
- 7.11 Video Port Interface (VPIF)
- 7.12 Transport Stream Interface (TSIF)
- 7.13 Clock Recovery Generator (CRGEN)
- 7.14 Video Data Conversion Engine (VDCE)
- 7.15 Peripheral Component Interconnect (PCI)
- 7.16 Ethernet MAC (EMAC)
- 7.17 Management Data Input/Output (MDIO)
- 7.18 Host-Port Interface (HPI) Peripheral
- 7.19 USB 2.0 [see Note]
- 7.20 ATA Controller
- 7.21 VLYNQ
- 7.22 Multichannel Audio Serial Port (McASP0/1) Peripherals
- 7.23 Serial Peripheral Interface (SPI)
- 7.24 Universal Asynchronouse Receiver/Transmitter (UART)
- 7.25 Inter-Integrated Circuit (I2C)
- 7.26 Pulse Width Modulator (PWM)
- 7.27 Timers
- 7.28 General-Purpose Input/Output (GPIO)
- 7.29 IEEE 1149.1 JTAG
- 8 Mechanical Packaging and Orderable Information
TMS320DM6467T
www.ti.com
SPRS605C –JULY 2009–REVISED JUNE 2012
Table 3-18. Transport Stream Interface 1 (TSIF1) Terminal Functions
SIGNAL
TYPE
(1)
OTHER
(2) (3)
DESCRIPTION
NAME NO.
TSIF1 INPUT – UART0 MUXING (PINMUX0.TSSIMUX = 01)
IPD
TS1_CLKIN AC11 I TSIF1 receive clock input (I).
DV
DD33
This pin is multiplexed between UART0 and TSIF1.
URXD0/ IPD
AB13 I When TSIF1 input on UART0 muxing is enabled (PINMUX0.TSSIMUX = 01), this
TS1_DIN DV
DD33
pin is the serial data input, TS1_DIN (I).
This pin is multiplexed between UART0 and TSIF1.
URTS0/UIRTX0/ IPU When TSIF1 input on UART0 muxing is enabled (PINMUX0.TSSIMUX = 01), in
AA13 I/O/Z
TS1_EN_WAITO DV
DD33
synchronous mode, this pin is the data enable indicator (I) or in asynchronous
mode, this pin is the wait output, TS1_EN_WAITO (O/Z).
This pin is multiplexed between UART0 and TSIF1.
UTXD0/URCTX0/ IPD
Y13 I/O/Z When TSIF1 input on UART0 muxing is enabled (PINUMX0.TSSIMUX = 01), this
TS1_PSTIN DV
DD33
pin is the packet start indicator, TS1_PSTIN (I).
TSIF1 INPUT – VPIF DOUT MUXING (PINMUX0.TSSIMUX = 10)
IPD
TS1_CLKIN AC11 I TSIF1 receive clock input (I).
DV
DD33
This pin is multiplexed between VPIF and TSIF1.
VP_DOUT15/ IPD
AB8 I/O/Z When TSIF1 input on VPIF DOUT muxing is enabled (PINMUX0.TSSIMUX = 10),
TS1_DIN DV
DD33
this pin is the serial data input, TS1_DIN (I).
This pin is multiplexed between VPIF and TSIF1.
VP_DOUT13/ IPD When TSIF1 input on VPIF DOUT muxing is enabled (PINMUX0.TSSIMUX = 10), in
Y9 I/O/Z
TS1_EN_WAITO DV
DD33
synchronous mode, this pin is the data enable indicator (I) or in asynchronous
mode, this pin is the wait output, TS1_EN_WAITO (O/Z).
This pin is multiplexed between VPIF and TSIF1.
VP_DOUT14/ IPD When TSIF1 input on VPIF DOUT muxing is enabled (PINMUX0.TSSIMUX = 10), in
AC7 I/O/Z
TS1_PSTIN DV
DD33
synchronous/asynchronous modes, this pin is the packet start indicator,
TS1_PSTIN (I).
TSIF1 INPUT – VPIF DIN MUXING (PINMUX0.TSSIMUX = 11)
IPD
TS1_CLKIN AC11 I TSIF1 receive clock input (I).
DV
DD33
VP_DIN7/ This pin is multiplexed between VPIF, TSIF0, and TSIF1.
IPD
TS0_DOUT7/ Y14 I/O/Z When TSIF1 input on VPIF DIN muxing is enabled (PINMUX0.TSSIMUX = 11), in
DV
DD33
TS1_DIN synchronous/asynchronous modes, this pin is the serial data input, TS1_DIN (I).
This pin is multiplexed between VPIF, TSIF0, and TSIF1.
VP_DIN5/
IPD When TSIF1 input on VPIF DIN muxing is enabled (PINMUX0.TSSIMUX = 11), in
TS0_DOUT5/ AB14 I/O/Z
DV
DD33
synchronous mode, this pin is the data enable indicator (I) or in asynchronous
TS1_EN_WAITO
mode, this pin is the wait output, TS1_EN_WAITO (O/Z).
This pin is multiplexed between VPIF, TSIF0, and TSIF1.
VP_DIN6/
IPD When TSIF1 input on VPIF DIN muxing is enabled (PINMUX0.TSSIMUX = 11), in
TS0_DOUT6/ AA14 I/O/Z
DV
DD33
synchronous/asynchronous modes, this pin is the packet start indicator,
TS1_PSTIN
TS1_PSTIN (I).
(1) I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground, A = Analog signal
(2) IPD = Internal pulldown, IPU = Internal pullup. For more detailed information on pullup/pulldown resistors and situations where external
pullup/pulldown resistors are required, see Section 4.8.1, Pullup/Pulldown Resistors.
(3) Specifies the operating I/O supply voltage for each signal
Copyright © 2009–2012, Texas Instruments Incorporated Device Overview 55
Submit Documentation Feedback
Product Folder Link(s): TMS320DM6467T