Datasheet
Table Of Contents
- FEATURES
- DESCRIPTION
- DEVICE INFORMATION
- ABSOLUTE MAXIMUM RATINGS
- DISSIPATION RATINGS
- RECOMMENDED OPERATING CONDITIONS
- ELECTRICAL CHARACTERISTICS
- TYPICAL CHARACTERISTICS
- OVERVIEW
- HARDWARE RESET
- DIGITAL CONTROL SERIAL INTERFACE
- I2C CONTROL INTERFACE
- DIGITAL AUDIO DATA SERIAL INTERFACE
- RIGHT JUSTIFIED MODE
- LEFT JUSTIFIED MODE
- I2S MODE
- DSP MODE
- TDM DATA TRANSFER
- AUDIO DATA CONVERTERS
- AUDIO CLOCK GENERATION
- STEREO AUDIO ADC
- AUTOMATIC GAIN CONTROL (AGC)
- STEREO AUDIO DAC
- DIGITAL AUDIO PROCESSING
- DIGITAL INTERPOLATION FILTER
- DELTA-SIGMA AUDIO DAC
- AUDIO DAC DIGITAL VOLUME CONTROL
- ANALOG OUTPUT COMMON-MODE ADJUSTMENT
- AUDIO DAC POWER CONTROL
- AUDIO ANALOG INPUTS
- ANALOG INPUT BYPASS PATH FUNCTIONALITY
- ADC PGA SIGNAL BYPASS PATH FUNCTIONALITY
- INPUT IMPEDANCE AND VCM CONTROL
- PASSIVE ANALOG BYPASS DURING POWER DOWN
- MICBIAS GENERATION
- ANALOG FULLY DIFFERENTIAL LINE OUTPUT DRIVERS
- ANALOG HIGH POWER OUTPUT DRIVERS
- SHORT CIRCUIT OUTPUT PROTECTION
- CONTROL REGISTERS
- Output Stage Volume Controls
Output Stage Volume Controls
TLV320AIC32
SLAS479C – AUGUST 2005 – REVISED DECEMBER 2008 .............................................................................................................................................
www.ti.com
Page 0 / Register 43: Left DAC Digital Volume Control Register
BIT READ/ RESET DESCRIPTION
WRITE VALUE
D7 R/W 1 Left DAC Digital Mute
0: The left DAC channel is not muted
1: The left DAC channel is muted
D6 – D0 R/W 0000000 Left DAC Digital Volume Control Setting
0000000: Gain = 0.0-dB
0000001: Gain = – 0.5-dB
0000010: Gain = – 1.0-dB
…
1111101: Gain = – 62.5-dB
1111110: Gain = – 63.0-dB
1111111: Gain = – 63.5-dB
Page 0 / Register 44: Right DAC Digital Volume Control Register
BIT READ/ RESET DESCRIPTION
WRITE VALUE
D7 R/W 1 Right DAC Digital Mute
0: The right DAC channel is not muted
1: The right DAC channel is muted
D6 – D0 R/W 0000000 Right DAC Digital Volume Control Setting
0000000: Gain = 0.0-dB
0000001: Gain = – 0.5-dB
0000010: Gain = – 1.0-dB
…
1111101: Gain = – 62.5-dB
1111110: Gain = – 63.0-dB
1111111: Gain = – 63.5-dB
A basic analog volume control with range from 0 dB to -78 dB and mute is replicated multiple times in the output
stage network, connected to each of the analog signals that route to the output stage. In addition, to enable
completely independent mixing operations to be performed for each output driver, each analog signal coming into
the output stage may have up to seven separate volume controls. These volume controls all have approximately
0.5-dB step programmability over most of the gain range, with steps increasing slightly at the lowest attenuations.
Table 5 lists the detailed gain versus programmed setting for this basic volume control.
Table 5. Output Stage Volume Control Settings and Gains
Gain Setting Analog Gain Gain Setting Analog Gain Gain Setting Analog Gain Gain Setting Analog Gain
(dB) (dB) (dB) (dB)
0 0.0 30 -15.0 60 -30.1 90 -45.2
1 -0.5 31 -15.5 61 -30.6 91 -45.8
2 -1.0 32 -16.0 62 -31.1 92 -46.2
3 -1.5 33 -16.5 63 -31.6 93 -46.7
4 -2.0 34 -17.0 64 -32.1 94 -47.4
5 -2.5 35 -17.5 65 -32.6 95 -47.9
6 -3.0 36 -18.0 66 -33.1 96 -48.2
7 -3.5 37 -18.6 67 -33.6 97 -48.7
8 -4.0 38 -19.1 68 -34.1 98 -49.3
9 -4.5 39 -19.6 69 -34.6 99 -50.0
10 -5.0 40 -20.1 70 -35.1 100 -50.3
11 -5.5 41 -20.6 71 -35.7 101 -51.0
12 -6.0 42 -21.1 72 -36.1 102 -51.4
13 -6.5 43 -21.6 73 -36.7 103 -51.8
14 -7.0 44 -22.1 74 -37.1 104 -52.2
54 Submit Documentation Feedback Copyright © 2005 – 2008, Texas Instruments Incorporated
Product Folder Link(s): TLV320AIC32