Datasheet
Table Of Contents
- FEATURES
- DESCRIPTION
- DEVICE INFORMATION
- ABSOLUTE MAXIMUM RATINGS
- DISSIPATION RATINGS
- RECOMMENDED OPERATING CONDITIONS
- ELECTRICAL CHARACTERISTICS
- TYPICAL CHARACTERISTICS
- OVERVIEW
- HARDWARE RESET
- DIGITAL CONTROL SERIAL INTERFACE
- I2C CONTROL INTERFACE
- DIGITAL AUDIO DATA SERIAL INTERFACE
- RIGHT JUSTIFIED MODE
- LEFT JUSTIFIED MODE
- I2S MODE
- DSP MODE
- TDM DATA TRANSFER
- AUDIO DATA CONVERTERS
- AUDIO CLOCK GENERATION
- STEREO AUDIO ADC
- AUTOMATIC GAIN CONTROL (AGC)
- STEREO AUDIO DAC
- DIGITAL AUDIO PROCESSING
- DIGITAL INTERPOLATION FILTER
- DELTA-SIGMA AUDIO DAC
- AUDIO DAC DIGITAL VOLUME CONTROL
- ANALOG OUTPUT COMMON-MODE ADJUSTMENT
- AUDIO DAC POWER CONTROL
- AUDIO ANALOG INPUTS
- ANALOG INPUT BYPASS PATH FUNCTIONALITY
- ADC PGA SIGNAL BYPASS PATH FUNCTIONALITY
- INPUT IMPEDANCE AND VCM CONTROL
- PASSIVE ANALOG BYPASS DURING POWER DOWN
- MICBIAS GENERATION
- ANALOG FULLY DIFFERENTIAL LINE OUTPUT DRIVERS
- ANALOG HIGH POWER OUTPUT DRIVERS
- SHORT CIRCUIT OUTPUT PROTECTION
- CONTROL REGISTERS
- Output Stage Volume Controls
TLV320AIC32
SLAS479C – AUGUST 2005 – REVISED DECEMBER 2008 .............................................................................................................................................
www.ti.com
Page 0 / Register 10: Audio Serial Data Interface Control Register C
BIT READ/ RESET DESCRIPTION
WRITE VALUE
D7 – D0 R/W 00000000 Audio Serial Data Word Offset Control
This register determines where valid data is placed or expected in each frame, by controlling
the offset from beginning of the frame where valid data begins. The offset is measured from
the rising edge of word clock when in DSP mode.
00000000: Data offset = 0 bit clocks
00000001: Data offset = 1 bit clock
00000010: Data offset = 2 bit clocks
…
Note: In continuous transfer mode the maximum offset is 17 for I2S/LJF/RJF modes and 16
for DSP mode. In 256-clock mode, the maximum offset is 242 for I2S/LJF/RJF and 241 for
DSP modes.
11111110: Data offset = 254 bit clocks
11111111: Data offset = 255 bit clocks
Page 0 / Register 11: Audio Codec Overflow Flag Register
BIT READ/ RESET DESCRIPTION
WRITE VALUE
D7 R 0 Left ADC Overflow Flag
This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is
removed. The register bit reset to 0 after it is read.
0: No overflow has occurred
1: An overflow has occurred
D6 R 0 Right ADC Overflow Flag
This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is
removed. The register bit reset to 0 after it is read.
0: No overflow has occurred
1: An overflow has occurred
D5 R 0 Left DAC Overflow Flag
This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is
removed. The register bit reset to 0 after it is read.
0: No overflow has occurred
1: An overflow has occurred
D4 R 0 Right DAC Overflow Flag
This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is
removed. The register bit reset to 0 after it is read.
0: No overflow has occurred
1: An overflow has occurred
D3 – D0 R/W 0001 PLL R Value
0000: R = 16
0001 : R = 1
0010 : R = 2
0011 : R = 3
0100 : R = 4
…
1110: R = 14
1111: R = 15
42 Submit Documentation Feedback Copyright © 2005 – 2008, Texas Instruments Incorporated
Product Folder Link(s): TLV320AIC32