Datasheet
TLV320AIC3120
SLAS653A –FEBRUARY 2010–REVISED MAY 2012
www.ti.com
Page 0 / Register 49 (0x31): INT2 Control Register
READ/ RESET
BIT DESCRIPTION
WRITE VALUE
D7 R/W 0 0: Headset-insertion detect interrupt is not used in the generation of INT2 interrupt.
1: Headset-insertion detect interrupt is used in the generation of INT2 interrupt.
D6 R/W 0 0: Button-press detect interrupt is not used in the generation of INT2 interrupt.
1: Button-press detect interrupt is used in the generation of INT2 interrupt.
D5 R/W 0 0: DAC DRC signal-power interrupt is not used in the generation of INT2 interrupt.
1: DAC DRC signal-power interrupt is used in the generation of INT2 interrupt.
D4 R/W 0 0: ADC AGC noise interrupt is not used in the generation of INT2 interrupt.
1: ADC AGC noise interrupt is used in the generation of INT2 interrupt.
D3 R/W 0 0: Short-circuit interrupt is not used in the generation of INT2 interrupt.
1: Short-circuit interrupt is used in the generation of INT2 interrupt.
D2 R/W 0 0: Engine-generated interrupt is not used in the generation of INT2 interrupt.
1: Engine-generated interrupt is used in the generation of INT2 interrupt.
D1 R/W 0 0: DC measurement using delta-sigma audio ADC data-available interrupt is not used in the generation
of INT2 interrupt.
1: DC measurement using delta-sigma audio ADC data-available interrupt is used in the generation of
INT2 interrupt.
D0 R/W 0 0: INT2 is only one pulse (active-high) of typical 2-ms duration.
1: INT2 is multiple pulses (active-high) of typical 2-ms duration and 4-ms period, until flag registers 44
and 45 are read by the user.
Page 0 / Register 50 (0x32): Reserved
READ/ RESET
BIT DESCRIPTION
WRITE VALUE
D7-D0 R/W 0000 0000 Reserved. Write only reset values.
Page 0 / Register 51 (0x33): GPIO1 In/Out Pin Control
READ/ RESET
BIT DESCRIPTION
WRITE VALUE
D7–D6 R/W XX Reserved. Do not write any value other than reset value.
D5–D2 R/W 0000 0000: GPIO1 disabled (input and output buffers powered down)
0001: GPIO1 is in input mode (can be used as secondary BCLK input, secondary WCLK input,
secondary DIN input, ADC_WCLK input, Dig_Mic_In, or in ClockGen block).
0010: GPIO1 is used as general-purpose input (GPI).
0011: GPIO1 output = general-purpose output
0100: GPIO1 output = CLKOUT output
0101: GPIO1 output = INT1 output
0110: GPIO1 output = INT2 output
0111: GPIO1 output = ADC_WCLK output for codec interface
1000: GPIO1 output = secondary BCLK output for codec interface
1001: GPIO1 output = secondary WCLK output for codec interface
1010: GPIO1 output = ADC_MOD_CLK output for the digital microphone
1011: GPIO1 output = secondary DOUT for codec interface
1100–1111: Reserved
D1 R X GPIO1 input buffer value
D0 R/W 0 0: GPIO1 general-purpose output value = 0
1: GPIO1 general-purpose output value = 1
Page 0 / Register 52 (0x34): Reserved
READ/ RESET
BIT DESCRIPTION
WRITE VALUE
D7–D0 R/W XXXX XXXX Reserved. Do not write to this register.
92 REGISTER MAP Copyright © 2010–2012, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TLV320AIC3120