TV Converter Box User Manual

Operational Overview
8 SLAA040
3.3.1 Jumpers Used on the TLV1562EVM
Table 2. 3-Position Jumpers
JUMPER GENERAL DESCRIPTION PIN 1-2 PIN 2-3
W1 Connects BP/CH3 (ADC) to R45 or GND; Input not in use, grounded to reduce noise Use as single input channel3 or
differential input positive channel B
W2 Connects BM/CH4 (ADC) to R44 or GND; Input not in use, grounded to reduce noise Use as single input channel4 or
differential input negative channel B
W3 Connects RD to XF or /RD1 Logic generator is connected to the ADC DSP is connected to the ADC
W4 WR + WR1 is connected with DSP_WR or
U12-J9/3
Logic generator is connected to the ADC DSP is connected to the ADC
W5
W6
W7
The three Jumpers define the prescaling of the
CLKOUT signal to the MCB_CLK Pin, if W8 is
set to Counter-Mode
W8 MCB_CLK is connected to BUFCLK (U14) or
RD1
(U11)
Counter-Mode (MCB_CLK signal is
divided by the counter, set-up with
Jumper W(5-7)
Counter-Mode disabled (MCB_CLK is
synchronize with the CLKOUT signal)
W9 CLK input of the Counter (U2) is connected with
CLKOUT or CLKOUT/2
The counter is toggled by the DSP
system clock (signal BUFF_CLK)
The counter’s clock is prescaled by two
(toggled by half the DSP system clock
(CLKOUT2))
W10 ADC CLKIN is connected to CLK/2 or CLK/4 The ADC clock runs at a quarter of the
DSP clock frequency (10 MHz)
The ADC clock runs at half the DSP
clock frequency (20 MHz)
W11 Connects AP/CH1 (ADC) to R48 or GND; Input not in use, grounded to reduce
noise
Use as single input channel 1 or
differential input positive channel A
W12 Connects AM/CH2 (ADC) to R47 or GND; Input not in use, grounded to reduce
noise
Use as single input channel 2 or
differential input negative channel A
W13 Connects REFLO (TLV5651) to Vcc or GND Disable internal reference Enable internal reference
W14 Connects SCLK (TLC5618AA) to BCLKX or J8
(BNC)
Normal DSP mode An external clock source drives the
SCLK pin instead of the DSP
W15 Connects CLK (TLV5651) to CLKOUT (DSP) or
J7 (BNC)
Normal DSP mode An external clock source drives the CLK
pin instead of the DSP
W23 Connects CSTART to A0, A1, or XF A0 and A1 used to generate ADC
CSTART
signal
XF signal connects to CSTART pin
W24 Connects DSP_RD to XF or IOSTRB, ORed with
R
/W from the DSP
XF signal connected to ADC RD pin RD pin driven by IOSTRB ORed with R/W
Table 3. 2-Position Jumpers
JUMPER GENERAL DESCRIPTION PINS SHORTED PINS OPEN
W16 Connects Mode input (TLV 5651) to GND MODE 0 is chosen (binary data input) MODE 1 is chosen (2s complement
data input)
W17 Connects REFIO (TLV5651) to VREF1 or leaves
the REFIO pin decoupled to GND via a 0.1 µF
capacitor
Use as external reference voltage input Use as internal reference voltage
output with this pin terminated into
GND in series with 0.1 pF
W18 Connects DIR (U19) to GND or leaves the DIR
pin connected to WR
ADC can only write but not read to the data
bus
Normal operation mode
W19 Connects OE (U19) to GND or leaves the OE pin
connected to CS
Output driver is isolated and disabled (no
signal can bus trough the data bus)
Normal operation mode
W20 Connects BDX to BDR or leaves BDR open DSP BDR pin gets a shortcuted feedback
from the BDX (transmit) pin; normal mode
BDR remains open
W21 Connects BSFX to BSFR or leaves BCLKR open DSP BSFR pin gets a shortcuted feedback
from the BSFX (transmit) pin; normal mode
BSFR remains open
W22 Connects BCLKX backwards with BCLKR or
leaves it open
DSP BCLKR pin gets a shortcuted feedback
from the BCLKX (transmit) pin; normal mode
BCLKR remains open
W28 Connect Sleep input (TLV5651/5 GND Normal mode of operation Sleep mode seleted