Datasheet
Table Of Contents
- 1 Introduction
- Table of Contents
- 2 Pin Descriptions
- 3 Configuration
- 4 Interfaces
- 5 Architecture
- 6 Reset and Power Down Operation
- 7 Design Guidelines
- 8 Register Block
- 8.1 Register Definition
- 8.1.1 Basic Mode Control Register (BMCR)
- 8.1.2 Basic Mode Status Register (BMSR)
- 8.1.3 PHY Identifier Register #1 (PHYIDR1)
- 8.1.4 PHY Identifier Register #2 (PHYIDR2)
- 8.1.5 Auto-Negotiation Advertisement Register (ANAR)
- 8.1.6 Auto-Negotiation Link Partner Ability Register (ANLPAR) (BASE Page)
- 8.1.7 Auto-Negotiate Expansion Register (ANER)
- 8.1.8 Auto-Negotiate Next Page Transmit Register (ANNPTR)
- 8.1.9 Auto-Negotiation Link Partner Ability Next Page Register (ANLNPTR)
- 8.2 Register Control Register (REGCR)
- 8.3 Address or Data Register (ADDAR)
- 8.4 Extended Registers
- 8.4.1 PHY Control Register (PHYCR)
- 8.4.2 PHY Status Register (PHYSR)
- 8.4.3 MII Interrupt Mask Register (MINTMR)
- 8.4.4 MII Interrupt Status Register (MINTSR)
- 8.4.5 MII Interrupt Control Register (MINTCR)
- 8.4.6 Receiver Error Counter Register (RECR)
- 8.4.7 BIST Control Register (BISCR)
- 8.4.8 BIST STATUS Register (BISSR)
- 8.4.9 BIST Byte Count Register (BISBCR)
- 8.4.10 BIST Error Count Register (BISECR)
- 8.4.11 BIST Packet Length Register (BISPLR)
- 8.4.12 BIST Inter Packet Gap Register (BISIPGR)
- 8.4.13 LED Direct Control Register (LEDCR)
- 8.4.14 Power Down Register (PDR)
- 8.4.15 False Carrier Sense Counter Register (FCSCR)
- 8.4.16 RX Channel Control Register (RXCCR)
- 8.5 Cable Diagnostic Registers
- 8.5.1 Cable Diagnostic Registers (CDCR)
- 8.5.2 Cable Diagnostic Status Register (CDSR)
- 8.5.3 Cable Diagnostic Results Register (CDRR)
- 8.5.4 TDR State Machine Enable (TDRSMR)
- 8.5.5 TDR Pattern Amplitude Register (TDRPAR)
- 8.5.6 TDR Manual Pulse Register (TDRMPR)
- 8.5.7 TDR Channel Silence Register (TDRCSR)
- 8.5.8 TDR Control Register (TDRCR)
- 8.5.9 TDR Clock Cycles Register (TDRLCR)
- 8.5.10 TDR Low Threshold Register (TDRLT1)
- 8.5.11 TDR Low Threshold Register (TDRLT2)
- 8.5.12 TDR Low Threshold Register (TDRLT3)
- 8.5.13 TDR Low Threshold Register (TDRLT4)
- 8.5.14 TDR High Threshold Register (TDRHT1)
- 8.5.15 TDR High Threshold Register (TDRHT2)
- 8.5.16 TDR High Threshold Register (TDRHT3)
- 8.5.17 TDR High Threshold Register (TDRHT4)
- 8.5.18 TDR Pattern Control Register 1 (TDRLCR1)
- 8.5.19 TDR Pattern Control Register 2 (TDRLCR2)
- 8.5.20 DSA Configuration Register 1 (DSACR1)
- 8.5.21 DSA Configuration Register 2 (DSACR2)
- 8.5.22 DSA Start Frequency (DSASFR)
- 8.5.23 DSA Frequency Control (DSAFCR)
- 8.5.24 DSA Output Control (DSAOCR)
- 8.5.25 RAM Control 1 (RAMCR1)
- 8.5.26 RAM Control 2 (RAMCR2)
- 8.5.27 RAM Data Out (RAMDR)
- 8.5.28 CD Pre Test Configuration Control 1 (CDPTC1R)
- 8.5.29 CD Pre Test Configuration Control 2 (CDPTC2R)
- 8.5.30 LPF Bypass (LPFBR)
- 8.1 Register Definition
- 9 Electrical Specifications
- 10 Appendix A: Digital Spectrum Analyzer (DSA) Output
- Revision History
RD–
RD–
RD+ RD+
49.9 W
49.9 W
Vdd
Vdd
0.1 Fm
0.1 F*m
TD– TD–
TD+
TD+
49.9 W
49.9 W
Vdd
0.1 Fm
0.1 F*m
1:1
1:1
T1
RJ45
Placeresistorsandcapacitorsclosetothedevice.
Common-modechokes
mayberequired.
Note:CentertapisconnectedtoVdd
*Placecapacitorsclosetothe
transformercentertaps
Allvaluesaretypicalandare 1%±
S0339-01
TLK100
SLLS931B–AUGUST 2009–REVISED DECEMBER 2009
www.ti.com
7 Design Guidelines
7.1 TPI Network Circuit
Figure 7-1 shows the recommended circuit for a 10/100 Mb/s twisted pair interface. Below is a partial list
of recommended transformers. It is important that the user realize that variations with PCB and
component characteristics require that the application be tested to verify that the circuit meets the
requirements of the intended application.
• Pulse H1102
• Pulse HX1188
Figure 7-1. 10/100 Mb/s Twisted Pair Interface
7.2 Clock In (XI) Requirements
The TLK100 supports an external CMOS-level oscillator source or an internal oscillator with an external
crystal.
7.2.1 Oscillator
If an external clock source is used, XI should be tied to the clock source and XO should be left floating.
The amplitude of the oscillator should be a nominal voltage of 1.8V.
36 Design Guidelines Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TLK100