User's Guide SLLU148 – May 2011 TLK10002 Dual-Channel, 10-Gbps, Multi-Rate Transceiver Evaluation Module This user’s guide describes the usage and construction of the TLK10002 evaluation module (EVM). This document provides guidance on proper use by showing some device configurations and test modes. In addition, design, layout, and schematic information is provided to the customer.
www.ti.com 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 2 .................................................................................................... Jitter Cleaner Control, Sheet 10 of 20 .................................................................................. Low-Speed Data Signals, Sheet 11 of 20 .............................................................................
www.ti.com 66 Common Signals, Sheet 4 of 4 .......................................................................................... 86 67 Top Signal, Layer 1 68 Internal Ground, Layer 2.................................................................................................. 89 69 Internal GND, Layers 3, 4, and 5 ........................................................................................ 90 70 Bottom Signal, Layer 6 ..........................................................
Introduction Introduction J4 J10 INB2P J11 INB2N J8 OUTB1N J12 OUTB2N OUTB0P OUTB0N J2 J6 INB1P J7 INB1N J5 J3 INB0P INB0N J9 OUTB1P MDC_POST_LS GND REV NA 1 www.ti.
EVM PCB and High-Speed Design Considerations www.ti.com bidirectional, point-to-point data transmission systems such as base station RRH (remote radio head) applications as well as any other high-speed application. All CPRI and OBSAI data rates from 1.2288 Gbps to 9.8304 Gbps and non-CPRI or OBSAI serial data rates between 1 Gbps and 10 Gbps are supported for the high-speed side.
TLK10002EVM Kit Contents • • • • 3 www.ti.com The entire board can be powered from a single, 5-V power supply where the power planes can be supplied through onboard regulators or through separate headers for isolation. Onboard capacitors provide ac coupling of high-speed transmit and receive signals. Voltage monitoring LED circuits provide quick indication that the voltage is within specification. Provisions are included for use of an onboard CDCE72010 jitter cleaner to supply a reference clock signal.
Control and Output Status Signals www.ti.com 5 Control and Output Status Signals All of the external control and status pins on the TLK10002EVM have been consolidated to a single location on the board and broken out into several header blocks for easier reference. LEDs have been added to the LOSA, LOSB, PRBS_PASS, and PLL_LOCK of the CDCE72010 jitter cleaner lines in addition to the headers for scope probes to allow easy monitoring of the high/low value on the line.
JTAG 7 www.ti.com JTAG The EVM also provides a separate connector to support the full five-pin JTAG interface of the TLK10002 with onboard level shifters to be compatible with most standard JTAG control interfaces to be used for manufacturing tests. The 3.3-V (header) side of the level shifter is connected to the header and the 1p5/8V side of the level shifter is connected to the TLK10002.
Test and Setup Configurations www.ti.com Depending on the power down and/or GUI termination sequence followed, the USB device may need to be RESET to allow re-enumeration to occur in future tests. When the board is powered on and the USB connection is enumerated, the USB online LED (D4) lights. If this LED fails to light, a PC-related issue may exist, and the PC must be restarted. The LED lights once the PC error is fixed.
Test and Setup Configurations JITTER PLL C76 U12 1p5V REG U16 JMP9 C94 C87 C85 6522850 GND JMP68 C98 GND GND VDDT C93 C95 GND JMP1 1p0V ANALOG VDDA C80 C121 C120 C111 C110 REF CLK1n C23 REF CLK0p REFCLK0n C109 J6 C119 J43 HSTXBn HSTXBp C20 C18 EN DVDD C117 C23 7 GND J44 J42 U8 R52 JMP69 U79 U76 C271 R69 C107 JMP55 C27 C25 VDDD JMP3 J71 J41 TLK10002 EVM MOTHER BOARD REV NA JMP67 1p0V DIGITAL EN GND P2 PLUG JMP70 C91 C89 U73 C90 C115 JMP74 C11
Test and Setup Configurations U39 D45 D44 VCCMGT_1P2V 1P2V_GTP U34 D42 1P2V U31 P1 +5V +5V U33 U30 U42 P3 GND R55 U36 D43 VCCINT_1P2V D51 D50 VCCCLK_3P3V 3P3V U43 D48 2P5V U40 JMP4 D49 VCCAUX_2P5V D47 VCCO_1P8V U37 1P8V D46 www.ti.
Test and Setup Configurations www.ti.
Test and Setup Configurations JTAG D45 C54 +5V Q17 GND EN JMP3 18 19 GND RE-PROGRAM FPGA CLK1 JMP22 GCLK25 IO SIGNALS GCLK27 GCLK12 GCLK17 USB RESET USB R30 R40 R31 R32 J2 SW4 R26 R33 SW8 MDIO 3P3V 2P5V Q31 R199 Q32 R214 R213 JMP20 R197 JMP19 MDIO C233 R132 MAIN RESET C236 C261 D15 USB_SUSP D16 R134 C4 USB_ONLINE D14 USB_RST R2 USB_/RST U6 D13 R5 R9 R6 R3 C1 R38 R39 R352 R202 R201 R351 RST LED9 LED10 D9 R226 LS_OK_IN_B D10 R224 RST R131 R8 R10 SW6 C5 U5
Test and Setup Configurations www.ti.
Test and Setup Configurations www.ti.
Test and Setup Configurations JITTER PLL C76 U12 1p5V REG U16 C75 J11 INB2N J8 OUTB1N J12 OUTB2N J9 OUTB1P J13 OUTB2P MDIO_POST_LS GND MDC_PRE_LS MDIO_PRE_LS REFCLK1p OUTB3P J17 J15 INB3N C2 29 37 C2 33 C2 41 C2 27 31 35 JMP1 C2 C2 C2 39 J72 LS_OK_IN_B LS_OK_OUT_B U1 J7 HSRXBn CHB_CLKOUTP J18 J37 CHA_CLKOUTN CHB_CLKOUTN J19 J36 CHA_CLKOUTP JMP2 40 36 C2 C2 32 TX DISABLE D49 C2 RX_LOS TX DISABLE D52 D50 28 TX_FAULT C2 MOD DETECT 38 D51 C2 34 J45 30
TLK10002EVM Motherboard Schematics www.ti.com 10 TLK10002EVM Motherboard Schematics 5 1 2 3 4 REVISIONS NOTES: ECR NUMBER DATE xx/xx/xx ------- ECR 1. PLACE NET NAMES ON ALL JUMPERS AND HEADERS. 2. PLACE ALL PARTS OTHER THAN SMP CONNECTORS ON A 0 OR 90 DEGREE ORIENTATION. 3. SERIAL DATA SHOULD BE ROUTED AS SINGLE-ENDED 50 OHM TRANSMISSION LINES ON OUTSIDE LAYERS. ROUTING DISTANCE SHOULD BE 3 INCHES OR LESS. 4. USE ROGERS MATERIAL FOR OUTSIDE LAYERS AND FR4-370 MATERIAL FOR INSIDE LAYERS. 5.
TLK10002EVM Motherboard Schematics www.ti.com 3P3V U7 D1 C1 USB_/RST_B 6 1 4 5 100K 100K R3 R5 2 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 38 8 9 4.99K R34 4.99K 4.99K R33 /VREN S2 S3 GND1 GND2 GND3 GND4 GND5 P3.0/S0/RXD P3.1/S1/TXD P3.2 P3.3 P3.4 P3.5 P3.6 P3.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 1.0V ANALOG REGULATOR 1.0V DIGITAL REGULATOR U8 DISABLE GND GND_PP 12 21 TPS74401RGW MUST USE TPS74401 3A LDO 1P0V_D_REG_EN NC1 NC2 NC3 DISABLE GND GND_PP 68uF 10uF 1uF C25 C27 1.13K 12 21 TPS74401RGW MUST USE TPS74401 3A LDO C28 0.001uF C24 16 FB 2 3 4 D R67 R66 1uF 4.99K 4.
TLK10002EVM Motherboard Schematics www.ti.com 2.5V REGULATOR 3.3V REGULATOR 12 21 GND GND_PP 1 2 3P3VREG_EN FB NC1 NC2 NC3 DISABLE GND GND_PP 16 12 21 TPS74401RGW C70 100pF 10uF 1uF C69 MUST USE TPS74401 3A LDO C R171 R154 C 9 13 14 17 68uF SS 2 3 4 D C68 NC4 NC5 NC6 3P3V 3.57K PG EN 1 18 19 20 C67 OUT1 OUT2 OUT3 OUT4 BIAS 15 1.54K MUST USE TPS74401 3A LDO IN1 IN2 IN3 IN4 R169 1uF C66 4.99K R168 4.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: 1210 SIZED 0 OHM RESISTORS HAVE BEEN INSTALLED FOR THE FERRITE BEADS. PLANE FILTERING / BULK DECOUPLING 3P3V_PLL 1P5/8V 1P0V_A L2 L1 VDDRA_LS VDDA D D 1P5/8V 1P0V_A 0.01uF 1uF 0.1uF C86 C87 10uF C85 L3 VDDRA_HS 2 C80 0.01uF 1uF 0.1uF C90 Ferrite Bead_1210 L4 1 3P3V_PLL 2 C91 10uF Ferrite Bead_1210 1 C89 0.01uF C83 2 C84 1uF 0.1uF C82 10uF C79 C81 1 1 VDDT 2 0.1uF C95 0.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTES: TLK10002 DEVICE POWER / LOCAL DECOUPLING DECOUPLLING GENERAL GUIDELINES: VDDA 1. PLACE CAPACITORS SUCH THAT SMALLER VALUE CAPACITORS ARE NEARER THE DUT AND THEN SUCCESSIVELY PLACE LARGER VALUE CAPACITORS AS YOU MOVE AWAY FROM THE DUT. NOTE: PLACE CAPACITORS NEAR VDDO NOTE: PLACE CAPACITORS TLK10002 DEVICE VDDA VDDO NEAR TLK10002 DEVICE U1K 0.1uF 0.1uF 0.1uF TLK10002 JMP71 C149 0.1uF C146 K7 C7 0.1uF 0.
TLK10002EVM Motherboard Schematics www.ti.com 5V I2C_REFCLKB_SEL_LS I2C_PRBSEN_LS I2C_LS_OK_IN_A_LS I2C_LS_OK_IN_B_LS 4.
TLK10002EVM Motherboard Schematics www.ti.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: 1. MATCH REFCLK0/1_P/N AND CLKOUT0/1_P/N TRACE LENGTHS TO EACHOTHER J41 REFCLK0P REFCLK0P_SMP J45 SMA SURFACE CLKOUTAP CLKOUTAP_SMP 0.1uF C191 OVERLAP CAPACITOR PADS U2N C193 DNI_0.1uF CLKOUTAP CLKOUTAP_PRI_REF_P C194 DNI_0.1uF REFCLK0N_U0N C195 DNI_0.1uF CLKOUTAN CLKOUTAN_PRI_REF_N C196 DNI_0.1uF DNI_150 DNI_150 CDCE72010 R499 R498 0.1uF C198 0.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 U2J JC_VCC_VCXO PLL_LOCK TESTOUTA CP_OUT D 56 JC_VBB 55 JC_STATUS JC_VCC_VCXO C272 0.1uF 50 1 JC_TESTOUTA 3 JC_CP_OUT R312 DNI_4.99K JITTER CLEANER LOOP FILTER VCXO_EN_NC 5V 1K 12K CDCE72010 C207 0.01uF R313 5K R314 7.15K C208 0.022uF R315 DNI_4.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: 1. MATCH LOW SPEED INPUT AND OUTPUT TRACE LENGTHS TO EACHOTHER 2. MATCH HIGH SPEED TRANSMIT AND RECEIVE TRACE LENGTHS TO EACHOTHER INA3P INB3P INA3P_CONNECTOR INSTALL 0-OHM RESISTOR C210 20 20 INB3P_CONNECTOR 0.1uF 0.1uF INA3N INSTALL 0-OHM RESISTOR INSTALL 0-OHM RESISTOR C211 INB3N C212 INA3N_CONNECTOR 20 20 INB3N_CONNECTOR INA2P_CONNECTOR 20 20 INB2P_CONNECTOR 0.1uF 0.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 3P3V J73B 1 U93 C1 100K 6 TX_DISABLE_/RST_B E1 THE MODULE. R548 C2 100K 4 TX_DISABLE_RST_B 7 9 RATE_SEL_0 RATE_SEL_1 10 11 14 VEER1 VEER2 VEER3 4 RX_LOS_B 100 RX_LOS_L 2 2 3 RX_LOS_C B2 E2 R551 1 17 20 C2 44.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF1 5V 5V 4P096V_REF2 5V 5V U44 3 U48A LM339A VCC GND R319 5V C260 0.47uF REF2940 12 + - 3 OUT 14 R329 3 IN_N 105K 3 IN_P R332 3.48K 9.
TLK10002EVM Motherboard Schematics www.ti.com 3 4 5 1 2 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF3 5V 5V 49.9 2 VOUT 49.9 U50 REF2940 5V 3 U51A LM339A VCC GND 12 1P5V_L C263 0.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF5 5V 5V 5V 4P096V_REF6 U56 2 IN_N + - 2 OUT U58 C2 LM339A + - 3 OUT 14 R368 3 IN_N 105K 3 IN_P R369 2K B VDDO_1P8V_B 8 49.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF7 5V 5V 4P096V_REF8 5V 5V U62 3 VDDT_L U67A LM339A VCC GND 14 VDDT_B 3 OUT 105K + - R388 3.48K 9.76K VDDT_0P85V_VREF 10 4 IN_P 4 IN_N + - 4 OUT R386 C2 DVDD_1P15V_VREF 9 8 DVDD 3 IN_N + - 3 OUT 14 R389 3.48K 13 11 R391 9.76K DVDD_0P85V_VREF 49.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE.
TLK10002EVM Motherboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF13 5V 5V 4P096V_REF14 5V 5V U81 U91 C2 LM339A 3 OUT 14 JC_VCCA_B + - R527 3 IN_N 105K 3 IN_P 3 JC_VCC_IN_3P0V_VREF 4 2 IN_N + - 2 OUT R522 10K JC_VCCA_3P0V_VREF 10 4 IN_P 4 IN_N + - C2 4P096V_REF14 LM339A U87D 1.
TLK10002EVM Motherboard Schematics www.ti.
TLK10002EVM Motherboard Bill of Materials www.ti.com 11 TLK10002EVM Motherboard Bill of Materials Table 1. TLK10002EVM Motherboard Bill of Materials Item Qty Reference Part Part Number Manufacturer 1 58 C191, C199, C210, C218, C226, C234, C243, C293, C198, 0.1μF C206, C217, C225, C233, C241, C290, 0201 CAP C0201X5R6R3-104KNE Venkel 2 64 C2, C4, C6, C7, C8, C12, C13, C14, C141, C142, 0.
TLK10002EVM Motherboard Bill of Materials www.ti.com Table 1. TLK10002EVM Motherboard Bill of Materials (continued) 38 Item Qty Reference Value Part Part Number Manufacturer 22 6 R296, R297, R308, R309, R451, R491 0.0 (Zero Ohm) 0201 RES CR0201-20W-000T Venkel 23 1 R535 100 0201 RES ERJ-1GEF1000C Panasonic - ECG 24 41 R273, R286, R445, R486, R507, R552 0402 RES ERJ-2GE0R00X Panasonic - ECG 25 1 R433 1.00K 0402 RES RG1005P-102-B-T5 Susumu Co Ltd 26 1 R24 1.
TLK10002EVM Motherboard Bill of Materials www.ti.com Table 1. TLK10002EVM Motherboard Bill of Materials (continued) Item Qty Reference Value Part Part Number Manufacturer 47 1 R322 6.04K 0402 RES RG1005P-6041-B-T5 Susumu Co Ltd 48 6 R326, R334, R382, R383, R390, R391 9.76K 0402 RES RG1005P-9761-B-T5 Susumu Co Ltd 49 2 R261, R269 0.0 (Zero Ohm) 0603 RES ERJ-3GEY0R00V Panasonic - ECG 50 2 R171, R188 1.10K 0603 RES RG1608P-112-B-T5 Susumu Co Ltd 51 2 R50, R67 1.
TLK10002EVM Motherboard Bill of Materials www.ti.com Table 1.
TLK10002EVM Motherboard Bill of Materials www.ti.com Table 1. TLK10002EVM Motherboard Bill of Materials (continued) Item Qty Reference Value Part Part Number Manufacturer 112 4 Standoff 10mm 10,15) .400 SO-1015-03-01-02 Samtec 113 4 Screws 4-40/0.25"- Screws 4-40/0.25"- Screws PMSSS 440 0025 PH Building Fasteners 114 4 Standoff 0.5" 0.5" 2027 Keystone Electronics 115 18 Shunt 0.1" SP 0.
TLK10002EVM Motherboard Layout 12 www.ti.com TLK10002EVM Motherboard Layout 6522850 TLK10002 EVM MOTHER BOARD REV NA JN Figure 29.
TLK10002EVM Motherboard Layout www.ti.com Figure 30.
TLK10002EVM Motherboard Layout www.ti.com Figure 31.
TLK10002EVM Motherboard Layout www.ti.com Figure 32.
TLK10002EVM Motherboard Layout www.ti.com VDDD VDDRB_HS VDDA VDDRB_LS VDDRA_HS 3P3V MDIO_LS_VCCB Figure 33.
TLK10002EVM Motherboard Layout www.ti.com JC_VCC_IN JC_VCCA VDDA 5V VDDT 3P3V_TX 3P3V_RX Figure 34.
TLK10002EVM Motherboard Layout www.ti.com 3P3V_PLL JC_VCC_OUT JC_VCC_VCXO VDDO DVDD VDDRA_LS 2P5V Figure 35.
TLK10002EVM Motherboard Layout www.ti.com Figure 36.
TLK10002EVM Motherboard Layout www.ti.com Figure 37.
TLK10002EVM Motherboard Layout www.ti.com Figure 38.
TLK10002EVM Motherboard Layout www.ti.com Table 2. TLK10002EVM Motherboard Layer Construction SUBCLASS NAME TOP L2_GND L3_SIG2 L4_GND L5_PWR L6_GND L7_GND L8_PWR L9_GND L10_PWR L11_GND L12_SIG3 L13_GND BOTTOM (1) 52 TYPE MATERIAL THICKNESS (MIL) DIELECTRIC CONSTANT LOSS TANGENT 1 WIDTH (MIL) SURFACE AIR CONDUCTOR COPPER DIELECTRIC Rogers PLANE COPPER DIELECTRIC FR-4 CONDUCTOR COPPER 1.2 1 0 DIELECTRIC FR-4 10 4.1 0.035 PLANE COPPER 1.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 13 TLK10002EVM FPGA Daughterboard Schematics 5 1 2 3 4 REVISIONS NOTES: ECR NUMBER ECR DATE xx/xx/xx ------- 1. PLACE NET NAMES ON ALL JUMPERS AND HEADERS. 2. PLACE ALL PARTS OTHER THAN SMA CONNECTORS ON A 0 OR 90 DEGREE ORIENTATION. 3. SERIAL DATA SHOULD BE ROUTED AS 100 OHM DIFFERENTIALLY COUPLED OR SINGLE-ENDED 50 OHM TRANSMISSION LINES ON OUTSIDE LAYERS. ROUTING DISTANCE SHOULD BE 5 INCHES OR LESS.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 3P3V U6 D13 C1 USB_/RST_B 6 1 C2 4 D15 R3 R5 2 USB_/RST USB_RST TPS3125J18 100K 0.1uF 0.1uF USB_RST_N VCC1 VCC2 VCC3 /RST 3 100K 0.1uF C6 PUR DM 22pF C8 1M 1 6 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 3P3V P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 R18 R17 100 USB ONLINE LED P3.0/S0/RXD P3.1/S1/TXD P3.2 P3.3 P3.4 P3.5 P3.6 P3.7 EE_SCL_S EE_SDA 12 11 SCL SDA DNI_4.99K DNI_4.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com TPS74401RGW JMP3 1 2 1P2VG_REG_EN C33 0.001uF DISABLE FB NC1 NC2 NC3 GND GND_PP Q17 12 21 TPS74401RGW 10uF 1uF 4.75K G S FDV301N R54 FDV301N 20 C 107 27 R55 4.99K R56 FDV301N C30 R52 R53 C D 16 GRD_1P2V_G 1.65K 68uF 13 14 17 C29 SS 9 2.49K NC4 NC5 NC6 C28 PG EN 1P2V_GTP R46 BIAS 1 18 19 20 R49 R51 G 2 3 4 OUT1 OUT2 OUT3 OUT4 1P2VG_REG_ADJ 1uF C27 4.7uF 4.99K R45 100uF C26 C25 10uF 68uF 3.
TLK10002EVM FPGA Daughterboard Schematics www.ti.
TLK10002EVM FPGA Daughterboard Schematics www.ti.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 1 2 3 4 5 U1E U1B 12 12 LS_A3_RX_P_CONNECTOR LS_A3_RX_N_CONNECTOR B10 A10 LS_A3_CLK_P C206 LS_A3_CLK_N 12 CHA_CLKN_CONNECTOR CHA_CLKP_CONNECTOR C201 0.1uF C203 0.1uF MGTRXP0_245 MGTRXN0_245 MGTREFCLK0P_245 MGTREFCLK0N_245 0.1uF C205 0.1uF VCCCLK_3P3V AC8 AD8 AE11 AF11 LS_B3_CLK_P C208 LS_B3_CLK_N 0.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 1 2 3 4 5 5V VCCO_1P8V VOLTAGE SUPERVISOR /MR 4 R131 130 VDD JMP12 1 2 MAIN_RST_SIGNAL SW8 TPS3125J18 4 3 1 2 5 VCCO_1P8V 2 Pin Berg MAIN RESET D22 PUSHBUTTON 1 U17 R149 JMP13 1 3 5 7 9 11 13 15 PRBSEN TEST_EN_A TEST_EN_B LANE2_4_SELECT_A LANE2_4_SELECT_B LOOPBACK_A LOOPBACK_B C1 20K MAIN_RST_B 2 4 6 8 10 12 14 16 6 E1 R150 C2 20K MAIN_/RST_B 4 1 MAIN_RST_C B1 2 1 PDTRXA_N 4.99K 4.99K 4.99K 4.99K 4.
TLK10002EVM FPGA Daughterboard Schematics www.ti.
TLK10002EVM FPGA Daughterboard Schematics www.ti.
TLK10002EVM FPGA Daughterboard Schematics www.ti.
G7 G8 F6 C3 B3 G6 F5 G9 A2 E6 E5 A4 A5 D13 A13 B12 B14 K12 J12 H15 J17 F17 E20 G17 B21 H18 H19 B24 A25 K18 K19 D23 C24 H21 H22 G23 J22 E23 E24 L19 K20 C25 C26 B26 K21 K22 M19 F23 G24 J23 J24 E25 E26 D24 D26 F24 F26 H24 H26 G25 G26 K24 K26 J25 J26 M24 M26 L25 L26 N25 N26 M21 M23 L20 L21 N17 N18 U23 U24 R25 R26 V23 W24 U25 U26 AD26 AB26 AC26 Y24 Y26 AE25 AE26 U21 C IO_L1N_VREF_0 IO_L2N_0 IO_L3N_0 IO_L4P_0 IO_L4N_0 IO_L5P_0 IO_L5N_0 IO_L13N_0 IO_L14N_0 IO_L8P_0 IO_L8N_VREF_0 IO_L22N_0 IO_L24N_0 IO_L34N_GCLK18
TLK10002EVM FPGA Daughterboard Schematics C A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A40 LS_B0_TX_P_CONNECTOR LS_B0_TX_N_CONNECTOR 6 6 LS_B0_RX_N_CONNECTOR LS_B0_RX_P_CONNECTOR 6 6 LS_B1_TX_P_CONNECTOR LS_B1_TX_N_CONNECTOR 6 6 LS_B1_RX_N_CONNECTOR LS_B1_RX_P_CONNECTOR 6 6 LS_B2_RX_N_CONNECTOR LS_B2_RX_P_CONNECTOR 6 6 LS_B2_TX_P_CONNECTOR LS_B2_TX_N_CONNECTOR 6 6 LS_B3_RX_N_CONNECTOR LS_B3
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF1 5V 5V 4P096V_REF2 5V 5V U29 2 OUT 2 U31 C2 4 LM339A U30D 9 8 3 IN_P 3 IN_N + - 3 OUT 14 R313 VCCINT_1P2V R316 2.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE.
TLK10002EVM FPGA Daughterboard Schematics www.ti.com 1 2 3 4 5 NOTE: VOLTAGE WINDOW DETECTOR CIRCUITS MONITOR THE VOLTAGE ON THE PLANE AND LIGHTS THE APPROPRIATE LED IF IT IS WITHIN THE ALLOWABLE DATASHEET RANGE. D D 4P096V_REF5 5V 5V 49.9 5V LM339A VCC GND 5V 12 4P096V_REF5 5V 5V_L 2 2 BLUE 1 BLUE 1 R345 2K D51 1 OUT R344 1 IN_N + - D50 6 3P3V 1 IN_P 105K 7 R342 LM339A U42B 1.65K 3P3V_3P6V_VREF 49.9 U42A VCCCLK_3P3V_L 3 C245 0.
TLK10002EVM FPGA Daughterboard Bill of Materials 14 www.ti.com TLK10002EVM FPGA Daughterboard Bill of Materials Table 3. TLK10002EVM FPGA Daughterboard Bill of Materials 68 Item Qty Reference Value Part Part Number Manufacturer 1 24 C201, C202, C203, C204, C205, C206, C207, C208, C215, C216, C219, C220, C221, C222, C223, C224, C225, C226, C227, C228, C229, C230, C231, C232 0.1μF 0201 CAP C0201X5R6R3-104KNE Venkel 2 164 C1, C2, C4, C5, C6, C10, C11, C12, 0.
TLK10002EVM FPGA Daughterboard Bill of Materials www.ti.com Table 3. TLK10002EVM FPGA Daughterboard Bill of Materials (continued) Item Qty Reference Value Part Part Number Manufacturer 10 6 C51, C56, C60, C64, C67, C72 0.01μF 0805 CAP GRM21BR72A103KA01L Murata Electronics North America 11 6 C49, C55, C59, C63, C68, C71 0.1μF 1206 CAP C1206C104J5RACTU Kemet 12 11 C18, C24, C30, C39, C45, C50, C54, C58, C62, C66, C70 1.
TLK10002EVM FPGA Daughterboard Bill of Materials www.ti.com Table 3. TLK10002EVM FPGA Daughterboard Bill of Materials (continued) 70 Item Qty Reference Value Part Part Number Manufacturer 29 2 R324, R332 12.4K 0402 RES RG1005P-1242-B-T5 Susumu Co Ltd 30 14 R67, R70, R131, R134, R188, R191, R269, R271, R276, R278, R285, R287, R292, R295 130 0402 RES RG1005P-131-B-T5 Susumu Co Ltd 31 1 R12 15.
TLK10002EVM FPGA Daughterboard Bill of Materials www.ti.com Table 3. TLK10002EVM FPGA Daughterboard Bill of Materials (continued) Item Qty Reference Value Part Part Number Manufacturer 43 1 R51 1.65K 0603 RES RG1608P-1651-B-T5 Susumu Co Ltd 44 2 R54, R65 107 0603 RES RR0816P-1070-B-T5-04A Susumu Co Ltd 45 2 R46, R60 2.49K 0603 RES RG1608P-2491-B-T5 Susumu Co Ltd 46 1 R50 2.80K 0603 RES RR0816P-2801-D-44H Susumu Co Ltd 47 1 R63 1.
TLK10002EVM FPGA Daughterboard Bill of Materials www.ti.com Table 3.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 15 TLK10002EVM FPGA Daughterboard Layout 1 TLK10002 EVM FPGA DAUGHTER BOARD REV NA 6522851 JN Figure 54.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 2 Figure 55.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 3 Figure 56.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 4 Figure 57.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 5 3P3V VCCINT_1P2V VCCMGT_1P2V Figure 58.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 8 VCCO_1P8V 2P5V Figure 59.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 10 5V VCCAUX_2P5V VCCCLK_3P3V Figure 60.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 12 Figure 61.
TLK10002EVM FPGA Daughterboard Layout www.ti.com 14 Figure 62.
TLK10002EVM FPGA Daughterboard Layout www.ti.com Table 4.
TLK10002EVM SMA Breakout Board Schematics www.ti.com 16 TLK10002EVM SMA Breakout Board Schematics 5 1 2 3 4 RE VIS IONS NOTES : ECR NU M BER ECR DA TE xx/xx/ xx ------- 1. PLACE NET NAMES ON ALL JUMPERS A ND HEADERS . 2. PLACE ALL PA RTS OTHER THAN SMA CONNECTORS ON A 0 OR 90 DE GREE ORI ENTA TION. 3. SERIAL DATA SHOULDB E ROUTED A S 100 OHM DIFFE RENTIA LLY COUPLED ORS INGLE-ENDE D50 OHM TRANS MISS ION LI NE S ON OUTSI DE LAYERS. ROUTING DI STANCE SHOULD BE 5 INCHES OR LESS.
TLK10002EVM SMA Breakout Board Schematics www.ti.
TLK10002EVM SMA Breakout Board Schematics www.ti.
TLK10002EVM SMA Breakout Board Schematics 5 www.ti.
TLK10002EVM SMA Breakout Board Schematics www.ti.com Table 5. TLK10002EVM SMA Breakout Board Bill of Materials Item Qty Reference Value Part Part_Number Manufacturer 1 1 J1 Board to Board Connector SMT ASP-134488-01 Samtec 2 5 JMP1, JMP2, JMP3, JMP4, JMP5 2X2 0.1x0.
TLK10002EVM SMA Breakout Board Layout 17 www.ti.com TLK10002EVM SMA Breakout Board Layout JN TLK10002 EVM SMA BREAKOUT DAUGHTER BOARD REV NA 6522852 Figure 67.
TLK10002EVM SMA Breakout Board Layout www.ti.com Figure 68.
TLK10002EVM SMA Breakout Board Layout www.ti.com Figure 69.
TLK10002EVM SMA Breakout Board Layout www.ti.com Figure 70.
TLK10002EVM SMA Breakout Board Layout www.ti.com Table 6. TLK10002EVM SMA Breakout Board Layer Construction SUBCLASS NAME TOP L2_GND1 L3_GND2 L4_GND3 L13_GND4 BOTTOM (1) 92 TYPE MATERIAL THICKNESS (MIL) DIELECTRIC CONSTANT LOSS TANGENT 1 WIDTH (MIL) SURFACE AIR CONDUCTOR COPPER DIELECTRIC FR-4 PLANE COPPER DIELECTRIC FR-4 PLANE COPPER DIELECTRIC FR-4 PLANE COPPER 1.2 1 0 DIELECTRIC FR-4 20 4.1 0.035 PLANE COPPER 1.2 1 0 DIELECTRIC FR-4 5 4.1 0.
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.