Datasheet
SLOS019E − SEPTEMBER 1988 − REVISED FEBRUARY 2005
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics at specified free-air temperature, V
DD
± = ±5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
T
A
†
TLC2652Q
TLC2652M
TLC2652AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
V
IO
Input offset voltage
25°C 0.6 3.5 0.5 3
V
V
IO
Input offset voltage
(see Note 7)
Full range 10 8
µV
VIO
Temperature coefficient of
Full range
0.003
0.03
∗
0.003
0.03
∗
V/°C
α
VIO
Temperature coefficient of
input offset voltage
Full range 0.003 0.03
∗
0.003 0.03
∗
µV/°C
Input offset voltage
long-term drift (see Note 4)
V
IC
= 0, R
S
= 50 Ω
25°C
0.003 0.06
∗
0.003 0.02
∗
µV/mo
I
IO
Input offset current
25°C 2 60 2 60
pA
I
IO
Input offset current
Full range 500 500
pA
I
IB
Input bias current
25°C 4 60 4 60
pA
I
IB
Input bias current
Full range 500 500
pA
Common-mode input
−5
−5
V
ICR
Common-mode input
voltage range
R
S
= 50
Ω
Full range
−5
to
−5
to
V
V
ICR
voltage range
R
S
= 50 Ω
Full range
to
3.1
to
3.1
V
V
OM+
Maximum positive peak
R
L
= 10 kΩ
See Note 5
25°C 4.7 4.8 4.7 4.8
V
V
OM+
Maximum positive peak
output voltage swing
R
L
= 10 kΩ,
See Note 5
Full range
4.7 4.7
V
V
OM−
Maximum negative peak
R
L
= 10 kΩ
See Note 5
25°C −4.7 −4.9 −4.7 −4.9
V
V
OM−
Maximum negative peak
output voltage swing
R
L
= 10 kΩ,
See Note 5
Full range
−4.7 −4.7
V
A
VD
Large-signal differential
V
O
= ±4 V,
R
L
= 10 kΩ
25°C 120 150 135 150
dB
A
VD
Large-signal differential
voltage amplification
V
O
= ±4 V,
R
L
= 10 kΩ
Full range
120 120
dB
f
ch
Internal chopping frequency 25°C 450 450 Hz
Clamp on-state current
V
O
= −5 V to 5 V
25°C 25 25
A
Clamp on-state current V
O
= −5 V to 5 V
Full range 25 25
µA
Clamp off-state current
R
L
= 100 kΩ
25°C 100 100
pA
Clamp off-state current R
L
= 100 kΩ
Full range 500 500
pA
CMRR
Common-mode rejection
V
O
= 0, V
IC
= V
ICR
min,
25°C 120 140 120 140
dB
CMRR
Common-mode rejection
ratio
V
O
= 0, V
IC
= V
ICR
min,
R
S
= 50 Ω
Full range 120 120
dB
k
SVR
Supply-voltage rejection
V
DD±
= ±1.9 V to ±8 V, 25°C 110 135 110 135
dB
k
SVR
Supply-voltage rejection
ratio (∆V
DD±
/∆V
IO
)
V
O
= 0,
R
S
= 50 Ω Full range 110 110
dB
I
DD
Supply current
V
O
= 0,
No load
25°C 1.5 2.4 1.5 2.4
mA
I
DD
Supply current
V
O
= 0,
No load
Full range 2.5 2.5
mA
∗
On products compliant to MIL-PRF-38535, this parameter is not production tested.
†
Full range is −40° to 125°C for Q suffix, −55° to 125°C for M suffix.
NOTES: 4. Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T
A
= 150°C extrapolated
at T
A
= 25° using the Arrhenius equation and assuming an activation energy of 0.96 eV.
5. Output clamp is not connected.
7. This parameter is not production tested. Thermocouple effects preclude measurement of the actual V
IO
of these devices in high
speed automated testing. V
IO
is measured to a limit determined by the test equipment capability at the temperature extremes. The
test ensures that the stabilization circuitry is performing properly.