Datasheet
TL750L
TL751L
www.ti.com
.................................................................................................................................... SLVS017U –SEPTEMBER 1987–REVISED SEPTEMBER 2009
TL75xL10 Electrical Characteristics
(1)
V
I
= 14 V, I
O
= 10 mA, T
J
= 25°C (unless otherwise noted)
TL750L10
TL751L10
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX
T
J
= 25°C 9.6 10 10.4
Output voltage V
I
= 11 V to 26 V, I
O
= 0 to 150 mA V
T
J
= 0°C to 125°C 9.5 10.5
V
I
= 12 V to 19 V 10 25
Input regulation voltage mV
V
I
= 11 V to 26 V 30 60
Ripple rejection V
I
= 12 V to 22 V, f = 120 Hz 60 65 dB
Output regulation voltage I
O
= 5 mA to 150 mA 50 100 mV
I
O
= 10 mA 0.2
Dropout voltage V
I
O
= 150 mA 0.6
Output noise voltage f = 10 Hz to 100 kHz 700 μV
I
O
= 150 mA 10 12
Quiescent current V
I
= 11 V to 26 V, I
O
= 10 mA, T
J
= 0°C to 125°C 1 2 mA
ENABLE ≥ 2 V 0.5
(1) Pulse-testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects
must be taken into account separately. All characteristics are measured with a 0.1-μF capacitor across the input and a 10-μF capacitor,
with equivalent series resistance of less than 0.4 Ω, across the output.
TL75xL12 Electrical Characteristics
(1)
V
I
= 14 V, I
O
= 10 mA, T
J
= 25°C (unless otherwise noted)
TL750L12
TL751L12
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX
T
J
= 25°C 11.52 12 12.48
Output voltage V
I
= 13 V to 26 V, I
O
= 0 to 150 mA V
T
J
= 0°C to 125°C 11.4 12.6
V
I
= 14 V to 19 V 15 30
Input regulation voltage mV
V
I
= 13 V to 26 V 20 40
Ripple rejection V
I
= 13 V to 23 V, f = 120 Hz 50 55 dB
Output regulation voltage I
O
= 5 mA to 150 mA 50 120 mV
I
O
= 10 mA 0.2
Dropout voltage V
I
O
= 150 mA 0.6
Output noise voltage f = 10 Hz to 100 kHz 700 μV
I
O
= 150 mA 10 12
Quiescent current V
I
= 13 V to 26 V, I
O
= 10 mA, T
J
= 0°C to 125°C 1 2 mA
ENABLE ≥ 2 V 0.5
(1) Pulse-testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible. Thermal effects
must be taken into account separately. All characteristics are measured with a 0.1-μF capacitor across the input and a 10-μF capacitor,
with equivalent series resistance of less than 0.4 Ω, across the output.
PARAMETER MEASUREMENT INFORMATION
The TL750L, TL751L series are low-dropout regulators. This means that capacitance loading is important to the
performance of the regulator because it is a vital part of the control loop. The capacitor value and its equivalent
series resistance (ESR) both affect the control loop and must be defined for the load range and temperature
range. Figure 1 shows the recommended range of ESR for a given load with a 10-μF capacitor on the output.
Copyright © 1987–2009, Texas Instruments Incorporated Submit Documentation Feedback 5