Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsLinear ICsLinear IC - Op-amp J-FET SOIC 8

1OUT

1IN−

1IN+

CC+

2IN+

2IN−

2OUT

4OUT

4IN−

4IN+

CC−

3IN+

3IN−

3OUT

TL074

D PACKAGE

(TOP VIEW)

1OUT

1IN−

1IN+

CC−

CC+

2OUT

2IN−

2IN+

TL072

D PACKAGE

(TOP VIEW)

TL072-EP, TL074-EP

www.ti.com

SLOS747F –OCTOBER 2011–REVISED DECEMBER 2012

LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIER

Check for Samples: TL072-EP, TL074-EP

FEATURES

• Low Power Consumption

• Wide Common-Mode and Differential Voltage

Ranges

• Low Input Bias and Offset Currents

• Output Short-Circuit Protection

• Low Total Harmonic Distortion: 0.003% Typ

• Low Noise

= 18 nV/√Hz Typ at f = 1 kHz

• High Input Impedance: JFET Input Stage

• Internal Frequency Compensation

• Latch-Up-Free Operation

• High Slew Rate: 13 V/μs Typ

• Common-Mode Input Voltage Range Includes

CC+

SUPPORTS DEFENSE, AEROSPACE,

AND MEDICAL APPLICATIONS

• Controlled Baseline

• One Assembly and Test Site

• One Fabrication Site

• Available in Extended (–40°C to 125°C) or

Military (–55°C to 125°C) Temperature Range

• Extended Product Life Cycle

• Extended Product-Change Notification

• Product Traceability

DESCRIPTION/ORDERING INFORMATION

The JFET-input operational amplifiers in the TL07x is similar to the TL08x series, with low input bias and offset

currents and fast slew rate. The low harmonic distortion and low noise make the TL07x ideally suited for high-

fidelity and audio preamplifier applications. Each amplifier features JFET inputs (for high input impedance)

coupled with bipolar output stages integrated on a single monolithic chip.

The TL07x is characterized for operation over the extended temperature range of –40°C to 125°C or military

temperature range of –55°C to 125°C.

ORDERING INFORMATION

(1)

maX ORDERABLE TOP-SIDE

PACKAGE VID NUMBER

AT 25°C PART NUMBER MARKING

TL072QDREP TL072Q V62/12604-01XE

–40°C to 125°C 6 mV SOIC – D Reel of 2500

TL074QDREP TL074Q V62/11621-01XE

Reel of 2500 TL074MDREP TL074M V62/11621-02XE

–55°C to 125°C 6 mV SOIC – D

Tube of 75 TL074MDEP TL074M V62/11621-02XE-T

(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI

website at www.ti.com.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (19 pages)

PAGE 1
TL072-EP, TL074-EP www.ti.com SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 LOW-NOISE JFET-INPUT OPERATIONAL AMPLIFIER Check for Samples: TL072-EP, TL074-EP FEATURES 1 • • Low Power Consumption Wide Common-Mode and Differential Voltage Ranges Low Input Bias and Offset Currents Output Short-Circuit Protection Low Total Harmonic Distortion: 0.
PAGE 2
TL072-EP, TL074-EP SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 www.ti.com TL072 and TL074 SYMBOL (EACH AMPLIFIER) IN+ + IN− − OUT SCHEMATIC (EACH AMPLIFIER) VCC+ IN+ 64 Ω IN− 128 Ω OUT 64 Ω C1 18 pF ÎÎÎ ÎÎÎ ÎÎÎ 1080 Ω 1080 Ω VCC− All component values shown are nominal.
PAGE 3
TL072-EP, TL074-EP www.ti.
PAGE 4
TL072-EP, TL074-EP SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 www.ti.
PAGE 5
TL072-EP, TL074-EP www.ti.com SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 PARAMETER MEASUREMENT INFORMATION 10 kΩ 1 kΩ − − VI VO VO + + VI CL = 100 pF RL RL = 2 kΩ Figure 1. Unity-Gain Amplifier CL = 100 pF Figure 2.
PAGE 6
TL072-EP, TL074-EP SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. INPUT BIAS CURRENT vs FREE-AIR TEMPERATURE 100 ±15 VOM VOM − Maximum Peak Output Voltage − V IIIB− IB Input Bias Current − nA VCC± = ±15 V 10 1 0.1 0.
PAGE 7
TL072-EP, TL074-EP www.ti.com SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 TYPICAL CHARACTERISTICS (continued) Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. MAXIMUM PEAK OUTPUT VOLTAGE MAXIMUM PEAK OUTPUT VOLTAGE vs vs FREE-AIR TEMPERATURE LOAD RESISTANCE ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ÏÏÏÏ ±15 RL = 10 kΩ ±12.
PAGE 8
TL072-EP, TL074-EP SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) VCC± = ±5 V to ±15 V RL = 2 kΩ TA = 25°C 105 104 0° Differential Voltage Amplification 103 45° 102 90° Phase Shift 101 135° 1 1 10 100 1k 10 k 100 k f − Frequency − Hz 1M 180° 10 M 1.01 1.1 Phase Shift 1 1 0.99 0.9 VCC± = ±15 V RL = 2 kΩ f = B1 for Phase Shift 0.8 0.
PAGE 9
TL072-EP, TL074-EP www.ti.com SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 TYPICAL CHARACTERISTICS (continued) Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. SUPPLY CURRENT PER AMPLIFIER TOTAL POWER DISSIPATION vs vs FREE-AIR TEMPERATURE FREE-AIR TEMPERATURE 250 VCC± = ±15 V No Signal No Load 1.8 1.6 1.4 1.2 ÁÁ ÁÁ ÁÁ ÁÁ ÁÁ 1 0.8 0.6 0.4 200 175 150 125 100 0.
PAGE 10
TL072-EP, TL074-EP SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. TOTAL HARMONIC DISTORTION VOLTAGE-FOLLOWER vs LARGE-SIGNAL PULSE RESPONSE FREQUENCY 6 0.4 VCC± = ±15 V AVD = 1 VI(RMS) = 6 V TA = 25°C VI and VO − Input and Output Voltages − V THD − Total Harmonic Distortion − % 1 0.1 0.01 0.004 0.
PAGE 11
TL072-EP, TL074-EP www.ti.com SLOS747F – OCTOBER 2011 – REVISED DECEMBER 2012 APPLICATION INFORMATION 1N4148 6 sin ωt 18 kΩ (see Note A) −15 V 18 pF 18 pF VCC+ VCC+ − 88.4 kΩ TL072 − + 6 cos ωt TL072 + 88.4 kΩ 1 kΩ VCC− 1 kΩ 18 pF VCC− 15 V 18 kΩ (see Note A) 1N4148 88.4 kΩ NOTE A: These resistor values may be adjusted for a symmetrical output. Figure 22.
PAGE 12
PACKAGE OPTION ADDENDUM www.ti.
PAGE 13
PACKAGE OPTION ADDENDUM www.ti.com (4) 4-Aug-2013 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device.
PAGE 14
PACKAGE MATERIALS INFORMATION www.ti.com 21-Dec-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TL074MDREP SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 TL074QDREP SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.
PAGE 15
PACKAGE MATERIALS INFORMATION www.ti.com 21-Dec-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL074MDREP SOIC D 14 2500 333.2 345.9 28.6 TL074QDREP SOIC D 14 2500 333.2 345.9 28.
PAGE 16
PAGE 17
PAGE 18
PAGE 19
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.