Datasheet

www.ti.com
THS7315EVM Bill of Materials
THS7315
SLOS532 – JUNE 2007
EVALUATION MODULE (continued)
Table 1. THS7315D EVM
MANUFACTURER DISTRIBUTOR
ITEM REF DES QTY DESCRIPTION SMD SIZE PART NUMBER PART NUMBER
1 FB1 1 Bead, Ferrite, 2.5A, 330 Ω 0805 (TDK) MPZ2012S331A (Digi-Key) 445-1569-1-ND
Capacitor, 100 μ F, Tantalum, 10V, 10%, (AVX)
2 C16 1 C (Digi-Key) 478-1765-1-ND
Low-ESR TPSC107K010R0100
3 C17, C18, C19 3 Open 0603
(Garrett)
4 C15 1 Capacitor, 0.1 μ F, Ceramic, 16V, X7R 0603 (AVX) 0603YC104KAT2A
0603YC104KAT2A
C1, C2, C3, C12,
5 6 OPEN 0805
C13, C14
6 C5 1 Capacitor, 0.01 μ F, Ceramic, 100V, X7R 0805 (AVX) 08051C103KAT2A (Digi-Key) 478-1358-1-ND
7 C7, C9, C11 3 Capacitor, 0.1 μ F, Ceramic, 50V, X7R 0805 (AVX) 08055C104KAT2A (Digi-Key) 478-1395-1-ND
8 C4 1 Capacitor, 1 μ F, Ceramic, 16V, X7R 0805 (TDK) C2012X7R1C105K (Digi-Key) 445-1358-1-ND
(Cornell)
9 C6, C8, C10 3 Capacitor, Aluminum, 470 μ F, 10V, 20% F (Newark) 97C7597
AFK477M10F24B
10 RX1–RX6 6 Open 0603
(Digi-Key)
11 R4–R9, Z1, Z2, Z3 9 Resistor, 0 Ω 0805 (ROHM) MCR10EZHJ000
RHM0.0ACT-ND
R1, R2, R3, R10, (Digi-Key)
12 6 Resistor, 75 Ω , 1/8W, 1% 0805 (ROHM) MCR10EZHF75.0
R11, R12 RHM75.0CCT-ND
Jack, Banana Receptance, 0.25" dia.
13 J9, J10 2 (SPC) 813 (Newark) 39N867
hole
J1, J2, J3, J6, J7, (Amphenol)
14 6 Connector, BNC, Jack, 75 Ω (Newark) 93F7554
J8 31-5329-72RFX
15 J4, J5 2 Connector, RCA, Jack, R/A (CUI) RCJ-32265 (Digi-Key) CP-1446-ND
16 TP1, TP2, TP3 3 Test Point, Red (Keystone) 5000 (Digi-Key) 5000K-ND
17 TP4, TP5 2 Test Point, Black (Keystone) 5001 (Digi-Key) 5001K-ND
18 U1 1 IC, THS7315 D (TI) THS7315D
19 4 Standoff, 4-40 Hex, 0.625" Length (Keystone) 1808 (Newark) 89F1934
20 4 Screw, Phillips, 4-40, .250" (BF) PMS 440 0031 PH (Digi-Key) H343-ND
21 1 Printed circuit board Edge # 6483760 REV. A
EVALUATION BOARD/KIT IMPORTANT NOTICE
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR
EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general
consumer use. Persons handling the product(s) must have electronics training and observe good engineering
practice standards. As such, the goods being provided are not intended to be complete in terms of required
design-, marketing-, and/or manufacturing-related protective considerations, including product safety and
environmental measures typically found in end products that incorporate such semiconductor components or
circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives
regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and
therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be
returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE
EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE.
20
Submit Documentation Feedback