Datasheet
SLOS214C − OCTOBER 1998 − REVISED MARCH 2007
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
preamp operating characteristics, G = 2, T
A
= 25°C, R
L
= 150 Ω, (unless otherwise noted)
PARAMETER TEST CONDITIONS
†
MIN TYP MAX UNIT
SR
Slew rate (see Note 4)
G = −1
V
O
= ±2 V,
V
CC
= ±5 V
65
V/ s
SR Slew rate (see Note 4) G = −1
V
O
= ±10 V,
V
CC
= ±15 V
85
V/µs
Settling time to 0.1%
V
CC
= ±5 V 85
t
s
Settling time to 0.1%
G = −1,
V
CC
= ±15 V 70
ns
t
s
Settling time to 0.01%
G = −1,
5 V Step
V
CC
= ±5 V 95
ns
Settling time to 0.01%
5 V Step
V
CC
= ±15 V 90
THD Total harmonic distortion
V
CC
= ±15 V,
V
O(PP)
= 2V
f
c
= 1 MHz,
R
L
= 250 Ω
−88 dBc
V
n
Input noise voltage V
CC
= ±5 V or ±15 V, f = 10 kHz 1.7 nV/√Hz
I
n
Input noise current V
CC
= ±5 V or ±15 V, f = 10 kHz 0.9 pA/√Hz
BW
Small-signal bandwidth (−3 dB)
V
O(PP)
= 0.4V,
V
CC
= ±5 V 85
MHz
BW Small-signal bandwidth (−3 dB)
V
O(PP)
= 0.4V,
G = 2
V
CC
= ±15 V 100
MHz
Bandwidth for 0.1 dB flatness
V
O(PP)
= 0.4V,
V
CC
= ±5 V 35
MHz
Bandwidth for 0.1 dB flatness
V
O(PP)
= 0.4V,
G = 2
V
CC
= ±15 V 45
MHz
Full power bandwidth (see Note 5)
V
CC
= ±5 V, V
O
= 5 V
O(PP)
4.1
MHz
Full power bandwidth (see Note 5)
V
CC
= ±15 V,
V
O
= 20 V
O(PP)
1.4
MHz
A
D
Differential gain error
G = 2, 100 IRE,
V
CC
= ±5 V 0.02%
A
D
Differential gain error
G = 2, 100 IRE,
NTSC
V
CC
= ±15 V 0.02%
φ
D
Differential phase error
G = 2, 100 IRE,
V
CC
= ±5 V 0.01°
φ
D
Differential phase error
G = 2, 100 IRE,
NTSC
V
CC
= ±15 V 0.01°
V
CC
= ±5 V,
V
O
= ±2.5 V,
T
A
= 25°C 85 89
Open loop gain
CC
V
O
=
±
2.5 V,
R
L
= 1 kΩ
T
A
= full range 83
dB
Open loop gain
V
CC
=
±
15 V,
T
A
= 25°C 86 91
dB
V
CC
= ±15 V,
V
O
= ±10 V, R
L
= 1 kΩ
T
A
= full range 84
Channel-to-channel crosstalk (THS7002) V
CC
= ±5 V or ±15 V, f = 1 MHz −85 dB
†
Full range for the THS7001/02C is 0°C to 70°C. Full range for the THS7001/02I is −40°C to 85°C.
NOTES: 4. Slew rate is measured from an output level range of 25% to 75%.
5. Full power bandwidth = slew rate/2π V
(PP)
.
shutdown electrical characteristics
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Standby current, disabled
Preamp
V
CC
= ±5 V 0.2 0.3
I
CC(standby)
Standby current, disabled
(per channel)
Preamp
V
I(SHDN)
= 2.5 V
V
CC
= ±15 V 0.65 0.8
mA
I
CC(standby)
(per channel)
PGA
V
I(SHDN)
= 2.5 V
V
CC
= ±5 V or ±15 V 0.8 1.2
mA
V
IH(SHDN)
Shutdown voltage for power up
V
CC
= ±5 V or ±15 V,
Relative to GND
0.8 V
V
IL(SHDN)
Shutdown voltage for power down
V
CC
= ±5 V or ±15 V, Relative to GND
2
V
I
IH(SHDN)
Shutdown input current high
V
CC
= ±5 V or ±15 V,
V
I(SHDN)
= 5 V
300 400 µA
I
IL(SHDN)
Shutdown input current low
V
CC
=
±
5 V or
±
15 V,
V
I(SHDN)
= 0.5 V
25 50 µA
t
dis
Disable time
†
V
CC
= ±5 V or ±15 V, Preamp and PGA 100 ns
t
en
Enable time
†
V
CC
= ±5 V or ±15 V, Preamp and PGA 1.5 µs
†
Disable time and enable time are defined as the interval between application of the logic signal to SHDN and the point at which the supply current
has reached half its final value.