Datasheet

ManualsBrandsTEXAS INSTRUMENTS ManualsInterface ICsInterface IC - drivers xDSL 2/0 HTSSOP 20

PWP 20-PinRHF 24-Pin

FEATURES DESCRIPTION

APPLICATIONS

−

1:1

CODEC

IN+

−

CODEC

IN−

30.1 Ω

1 μF 33nF

Line:

100 Ω

30.1 Ω

4.99kΩ

1.15kΩ

0.1 μF

LinePower= ADSL2:19.8dBm

ADSL2+:20.4dBm

ADSL2++:21.1dBm

12V

−12V

THS6184

www.ti.com

................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009

DUAL-PORT, LOW-POWER DIFFERENTIAL

xDSL LINE DRIVER AMPLIFIERS

• Trimmed Low-Power Consumption

The THS6184 is a dual-port, low-power current

feedback differential line driver amplifier system ideal

– 4.2-mA/amp Full Bias Mode; 4.8 mA Max

for xDSL systems. Its extremely low-power

– 3.2-mA/amp Mid Bias Mode; 3.7 mA Max

dissipation is ideal for ADSL, ADSL2, ADSL2+, and

– 2.15-mA/amp Low Bias Mode; 2.5 mA Max

ADSL2++ systems that must achieve high densities in

– Shutdown Mode and I

ADJ

Pin for Variable ADSL central office applications by combining two

ports, or four amplifiers, into one package.

Bias

• Low Noise

The unique architecture of the THS6184 allows the

trimmed quiescent current to be much lower than

– 3-nV/ √ Hz Voltage Noise

existing line drivers while still achieving high linearity.

– 5.9-pA/ √ Hz Inverting Current Noise

Distortion at these low-power levels is good with

– 1.2-pA/ √ Hz Noninverting Current Noise

– 83-dBc THD at 1 MHz with the low bias mode of 4.2

mA/port. Fixed and variable multiple-bias settings of

• Low MTPR Distortion

the amplifiers allows for enhanced power savings for

– – 74 dB with ADSL and ADSL2

line lengths where the full performance of the

– – 71 dB with ADSL2+ and – 70 dB with

amplifier is not required.

ADSL2++

The wide output swing of 44-V

differentially with

• – 83 dBc THD (1 MHz, 100- Ω Differential)

± 12-V power supplies coupled with over 415-mA

• High Output Current: >415 mA (25- Ω Load)

current drive allow for wide dynamic range, keeping

distortion minimized. With a low 3-nV/ √ Hz voltage

• Wide Output Swing: 44 V

( ± 12-V, 200- Ω

noise coupled with a low 5.9-pA/ √ Hz inverting current

Differential)

noise, the THS6184 increases the sensitivity of the

• Wide Bandwidth: 30 MHz (Gain = 5)

receive signals allowing for better margins and reach.

• Wide Power Supply Range: ± 4 V to ± 16 V

• Ideal For Power Sensitive, High Density ADSL,

ADSL2, ADSL2+, and ADSL2++ Systems

Figure 1. Typical Line Driver Circuit Using One Port of THS6184

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

2 PowerPAD is a trademark of Texas Instruments.

3 All other trademarks are the property of their respective owners.

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of the Texas

Instruments standard warranty. Production processing does not

necessarily include testing of all parameters.

Summary of content (39 pages)

PAGE 1
THS6184 RHF 24-Pin PWP 20-Pin www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 DUAL-PORT, LOW-POWER DIFFERENTIAL xDSL LINE DRIVER AMPLIFIERS FEATURES DESCRIPTION 1 • Trimmed Low-Power Consumption – 4.2-mA/amp Full Bias Mode; 4.8 mA Max – 3.2-mA/amp Mid Bias Mode; 3.7 mA Max – 2.15-mA/amp Low Bias Mode; 2.
PAGE 2
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
PAGE 3
THS6184 www.ti.com .................................................................................................................................................
PAGE 4
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com ELECTRICAL CHARACTERISTICS At VS = ±12 V: RF = 3 kΩ, RL = 50 Ω, G = 5, Radj = 0 Ω, full bias (unless otherwise noted) each amplifier independently tested.
PAGE 5
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ELECTRICAL CHARACTERISTICS (continued) At VS = ±12 V: RF = 3 kΩ, RL = 50 Ω, G = 5, Radj = 0 Ω, full bias (unless otherwise noted) each amplifier independently tested.
PAGE 6
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com ELECTRICAL CHARACTERISTICS At VS = ±5 V: RF = 3 kΩ, RL = 50 Ω, G = 5, Radj = 0, full bias (unless otherwise noted).
PAGE 7
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ELECTRICAL CHARACTERISTICS (continued) At VS = ±5 V: RF = 3 kΩ, RL = 50 Ω, G = 5, Radj = 0, full bias (unless otherwise noted).
PAGE 8
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com 12 V 0.01 μF VIN+ 30.1 Ω + Line Power = ADSL2: 19.8 dBm ADSL2+: 20.4 dBm ADSL2++: 21.1 dBm 1:1 − 7.5 kΩ 4.99 kΩ 1.15 kΩ 1 μF Line: 100 Ω 33 nF 0.1 μF 4.99 kΩ − Transformer Insertion Loss = 0.4 dB 30.1 Ω 0.01 μF + VIN− −12 V 7.5 kΩ PSD − Power Spectral Density − dBm/Hz Figure 2.
PAGE 9
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 TYPICAL CHARACTERISTICS Table 3.
PAGE 10
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com Table 4. Table of Graphs: ±5-V Operation GRAPH TITLE Large Signal Single-Ended Output Response, Full Bias CONDITIONS vs Frequency Large Signal Differential Output Response, Full vs Frequency Bias FIGURE G = 5, RL = 50 Ω, VO = 0.25 VPP – 4 VPP 41 G = 5, RL = 100 Ω, VO = 0.
PAGE 11
THS6184 www.ti.com .................................................................................................................................................
PAGE 12
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.
PAGE 13
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 TYPICAL CHARACTERISTICS (continued) SINGLE-ENDED 2ND-ORDER HARMONIC DISTORTION vs FREQUENCY, G = 5, RL = 50Ω DIFFERENTIAL HARMONIC DISTORTION vs FREQUENCY, G = 10, RL = 50 Ω −40 G = 10, Low, HD3 RF = 5 kΩ, RG = 1.
PAGE 14
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.
PAGE 15
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 TYPICAL CHARACTERISTICS (continued) OVERDRIVE RECOVERY vs TIME, G = 5, RL = 100Ω 2.4 12 G = 5, RF = 2 kΩ, RG = 499 Ω, RL = 100 Ω, VS = ±12 V Rising 350 1.6 300 4 0.8 0 0 −0.
PAGE 16
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS (continued) INPUT OFFSET VOLTAGE vs FREE-AIR TEMPERATURE INPUT OFFSET VOLTAGE vs INPUT COMMON-MODE RANGE 12.5 100 VS = ±15 V VOS − Input Offset Voltage − mV VOS − Input Offset Voltage − mV 12 11.5 VS = ±12 V 11 10.5 10 9.5 VS = ±5 V 9 8.
PAGE 17
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 TYPICAL CHARACTERISTICS (continued) LARGE SIGNAL SINGLE-ENDED OUTPUT RESPONSE, FULL BIAS vs FREQUENCY, G = 5, RL = 50Ω OUTPUT IMPEDANCE vs FREQUENCY, G = 5 1000 Large Signal Output Amplitude - dB (VPP) 15 100 G = +5, VS = ±12 V 10 Low Bias Mid Bias 1 Full Bias 0.
PAGE 18
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.
PAGE 19
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 APPLICATION INFORMATION The THS6184 contains four independent operational amplifiers. These amplifiers are current feedback topology amplifiers made for high-speed operation.
PAGE 20
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com DIE Side View (a) Thermal Pad DIE End View (b) Bottom View (c) A. The thermal pad is electrically isolated from all terminals in the package. Figure 52.
PAGE 21
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 OFFSET VOLTAGE The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times the corresponding gains.
PAGE 22
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com The total equivalent input noise density (eni) is calculated by using the following equation: e ni + Ǹ Where: 2 ǒenǓ ) ǒIN ) R Ǔ S 2 ǒ ) IN– ǒR F ø R G ǓǓ 2 ǒ ) 4 kTRs ) 4 kT R ø R F G Ǔ k = Boltzmann’s constant = 1.
PAGE 23
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 RG RF VO + VI R1 ǒ V − O + V I R 1) C1 f –3dB + R F G Ǔǒ Ǔ 1 1 ) sR1C1 1 2pR1C1 Figure 56. Single-Pole Low-Pass Filter If a multiple pole filter is required, the use of a Sallen-Key filter can work very well with CFB amplifiers.
PAGE 24
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com ground should also be used as previously stipulated. Because of its high power delivery, proper thermal management of the THS6184 is required.
PAGE 25
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 0,4953 0,1905 Pad Size 24 x (0,3048 x 0,762) mm 0,3721 0,1905 4,9022 2,2987 0,4953 0,3641 3,302 5,9182 PowerPAD and Via Layout (Pad Size 3,65 mm x 2,65 mm.
PAGE 26
THS6184 SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 ................................................................................................................................................. www.ti.com 1,3 0,65 Pad Size 20 x (0,3 x 1,6) mm 1,3 3,7 6,6 4,4 3 6,5 PowerPAD and Via Layout (Pad Size 3 mm x 3,7 mm. 9 Vias with Diameter = 0,3 mm) Vias should go through the board connecting the top PowerPAD to any and all ground planes.
PAGE 27
THS6184 www.ti.com ................................................................................................................................................. SLLS635D – AUGUST 2005 – REVISED JANUARY 2009 The actual thermal performance achieved with the THS6184 in the 24-pin RHF PowerPAD package or the 20-pin PWP PowerPAD package depends on the application.
PAGE 28
PACKAGE OPTION ADDENDUM www.ti.
PAGE 29
PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.
PAGE 30
PACKAGE MATERIALS INFORMATION www.ti.com 24-Jul-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) THS6184PWPR HTSSOP PWP 20 2000 330.0 16.4 THS6184RHFR VQFN RHF 24 3000 330.0 THS6184RHFT VQFN RHF 24 250 180.0 6.95 7.1 1.6 8.0 16.0 Q1 12.4 4.3 5.3 1.3 8.0 12.0 Q1 12.4 4.3 5.3 1.3 8.0 12.
PAGE 31
PACKAGE MATERIALS INFORMATION www.ti.com 24-Jul-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) THS6184PWPR HTSSOP PWP 20 2000 367.0 367.0 38.0 THS6184RHFR VQFN RHF 24 3000 367.0 367.0 35.0 THS6184RHFT VQFN RHF 24 250 210.0 185.0 35.
PAGE 32
PAGE 33
PAGE 34
PAGE 35
PAGE 36
PAGE 37
PAGE 38
PAGE 39
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.