Datasheet

www.ti.com
THS6182
SLLS544H – SEPTEMBER 2002 – REVISED JUNE 2007
ELECTRICAL CHARACTERISTICS (continued)
over recommended operating free-air temperature range, T
A
= 25 ° C, V
CC
= ± 12 V, R
F
= 2 k Ω ,
Gain = +5, I
ADJ
= Bias1 = Bias2 = 0 V, R
L
= 50 Ω (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
OUTPUT CHARACTERISTICS
R
L
= 100 Ω ± 3.9 ± 4.1
V
CC
= ± 5 V V
R
L
= 25 Ω ± 3.7 ± 3.9
R
L
= 100 Ω ± 10.7 ± 11
V
O
Single-ended output voltage swing V
CC
= ± 12 V V
R
L
= 25 Ω ± 10 ± 10.6
R
L
= 100 Ω ± 13.5 ± 13.9
V
CC
= ± 15 V V
R
L
= 25 Ω ± 12.7 ± 13.4
R
L
= 5 Ω V
CC
= ± 5 V ± 350 ± 400
I
O
Output current
(1)
V
CC
= ± 12 V ± 450 ± 600 mA
R
L
= 10 Ω
V
CC
= ± 15 V ± 450 ± 600
I
(SC)
Short-circuit current
(1)
R
L
= 1 Ω V
CC
= ± 12 V 1000 mA
Output resistance Open-loop 6 Ω
Output resistance—terminate mode f = 1 MHz, Gain = +10 0.05 Ω
Output resistance—shutdown mode f = 1 MHz, Open-loop 8.5 k Ω
POWER SUPPLY
Dual supply ± 4 ± 12 ± 16.5
V
CC
Operating range V
Single supply 8 24 33
T
A
= 25 ° C 9.7 10.7
V
CC
= ± 5 V mA
T
A
= full range 11.7
Quiescent current (each driver)
(2)
T
A
= 25 ° C 11 12
Full-bias mode (Bias-1 = 0,
V
CC
= ± 12 V mA
Bias-2 = 0)
T
A
= full range 12.5
(Trimmed with V
CC
= ± 12 V at 25 ° C)
I
CC
T
A
= 25 ° C 11.5 12.5
V
CC
= ± 15 V mA
T
A
= full range 13
Mid; Bias-1 - 1, Bias-2 = 0 7.5 8.5
Quiescent current (each driver)
Low; Bias-1 = 0, Bias-2 = 1 4 5 mA
Variable bias modes, V
CC
= ± 12 V
Shutdown; Bias-1 = 1, Bias-2 = 1 0.25 0.9
T
A
= 25 ° C -50 -56
V
CC
= ± 5 V,
∆ V
CC
= ± 0.5 V
T
A
= full range -47
PSRR Power supply rejection ratio dB
T
A
= 25 ° C -56 -60
V
CC
= ± 12 V, ± 15 V,
∆ V
CC
= ± 1 V
T
A
= full range -53
DYNAMIC PERFORMANCE
Gain = +1, RF = 1.2 k Ω 100
Gain = +2, RF = 1 k Ω 80
R
L
= 100 Ω MHz
Gain = +5, RF = 1 k Ω 35
Gain = +10, RF = 1 k Ω 20
Single-ended small-signal bandwidth
BW
(-3 dB), V
O
= 0.1 Vrms
Gain = +1, RF = 1.5 k Ω 65
Gain = +2, RF = 1 k Ω 60
R
L
= 25 Ω MHz
Gain = +5, RF = 1 k Ω 40
Gain = +10, RF = 1 k Ω 22
SR Single-ended slew rate
(3)
V
O
= 10 V
PP
, Gain = +5 450 V/ µ s
(1) A heatsink is required to keep the junction temperature below absolute maximum rating when an output is heavily loaded or shorted.
See Absolute Maximum Ratings section for more information.
(2) Approximately 0.5 mA (total) flows from V
CC+
to GND for internal logic control bias.
(3) Slew rate is defined from the 25% to the 75% output levels.
4
Submit Documentation Feedback