Datasheet

THS6012
www.ti.com SLOS226F –SEPTEMBER 1998–REVISED JUNE 2012
ELECTRICAL CHARACTERISTICS (continued)
V
CC
= ±15 V, R
L
= 25 Ω, R
F
= 1 kΩ, T
A
= 25°C (unless otherwise noted)
PARAMETER TEST CONDITIONS
(1)
MIN TYP MAX UNIT
V
O(PP)
= 20 V -65
V
CC
= ±15 V, R
F
= 680 Ω,
G = 2, f = 1 MHz
V
O(PP)
= 2 V -79
THD Total harmonic distortion dBc
V
CC
= ±5 V, R
F
= 680 Ω,
V
O(PP)
= 2 V -76
G = 2, f = 1 MHz
V
CC
= ±5 V or ±15 V, f = 10 kHz, G = 2, Single-
V
n
Input voltage noise 1.7 nV/√Hz
ended
Positive (IN+) 11.5
Input noise
I
n
V
CC
= ±5 V or ±15 V, f = 10 kHz, G = 2 pA/√Hz
current
Negative (IN-) 16
V
CC
= ±5 V 0.04%
G = 2, NTSC, 40 IRE
A
D
Differential gain error
R
L
= 150 Ω, Modulation
V
CC
= ±15 V 0.05%
V
CC
= ±5 V 0.07°
G = 2, NTSC, 40 IRE
φ
D
Differential phase error
R
L
= 150 Ω, Modulation
V
CC
= ±15 V 0.08°
Crosstalk Driver to driver V
I
= 200 mV, f = 1 MHz -62 dB
DC PERFORMANCE
V
CC
= ±5 V 1.5
Open loop transresistance MΩ
V
CC
= ±15 V 5
T
A
= 25°C 2 5
V
IO
Input offset voltage V
CC
= ±5 V or ±15 V mV
T
A
= full range 7
Input offset voltage drift V
CC
= ±5 V or ±15 V, T
A
= full range 20 μV/°C
T
A
= 25°C 1.5 4
Differential input offset voltage V
CC
= ±5 V or ±15 V mV
T
A
= full range 5
T
A
= 25°C 3 9
Negative μA
T
A
= full range 12
T
A
= 25°C 4 10
I
IB
Input bias current Positive V
CC
= ±5 V or ±15 V μA
T
A
= full range 12
T
A
= 25°C 1.5 8
Differential μA
T
A
= full range 11
Differential input offset voltage drift V
CC
= ±5 V or ±15 V, T
A
= full range 10 μV/°C
INPUT CHARACTERISTICS
V
CC
= ±5 V ±3.6 ±3.7
Common-mode input voltage
V
ICR
V
range
V
CC
= ±15 V ±13.4 ±13.5
Common-mode rejection ratio 62 70
CMRR V
CC
= ±5 V or ±15 V, T
A
= full range dB
Differential common-mode
100
rejection ratio
R
I
Input resistance 300 kΩ
C
I
Differential input capacitance 1.4 pF
OUTPUT CHARACTERISTICS
3 to 3.2 to
V
CC
= ±5 V
-2.8 -3
Single ended R
L
= 25 Ω V
11.8 to - 12.5 to -
V
CC
= ±15 V
11.5 12.2
Output voltage
V
O
swing
6 to 6.4 to
V
CC
= ±5 V
-5.6 -6
Differential R
L
= 50 Ω V
23.6 to - 25 to -
V
CC
= ±15 V
23 24.4
R
L
= 5 Ω, V
CC
= ±5 V 500
I
O
Output current
(2)
mA
R
L
= 25 Ω, V
CC
= ±15 V 400 500
(2) A heat sink is required to keep the junction temperature below absolute maximum when an output is heavily loaded or shorted. See
absolute maximum ratings and Thermal Information section.
Copyright © 1998–2012, Texas Instruments Incorporated 5