Datasheet
THS4513
www.ti.com
SLOS472E –AUGUST 2005–REVISED JANUARY 2013
ELECTRICAL CHARACTERISTICS: V
S+
– V
S–
= 3 V
Test conditions at V
S+
= 1.5 V, V
S–
= –1.5 V, G = 0 dB, CM = open, V
O
= 1 V
PP
, R
F
= 348 Ω, R
L
= 200-Ω differential,
T
A
= +25°C, single-ended input, differential output, and input and output referenced to midsupply, unless otherwise noted.
TEST
PARAMETER TEST CONDITIONS TYP UNIT
LEVEL
(1)
AC PERFORMANCE
G = 0 dB, V
O
= 100 mV
PP
1.6 GHz
Small-signal bandwidth
G = 6 dB, V
O
= 100 mV
PP
1.3 GHz
Gain-bandwidth product G = 6 dB 2.6 GHz
G = 0 dB, V
O
= 1 V
PP
135
Bandwidth for 0-dB Flatness MHz
G = 6 dB, V
O
= 1 V
PP
450
Large-signal bandwidth G = 10 dB, V
O
= 1 V
PP
1.4 GHz
Slew rate (differential) 2700 V/μs
Rise time 0.25
Fall time 1-V step 0.25
ns
Settling time to 1% 2.9
Settling time to 0.1% 16
f = 10 MHz –116
2nd-order harmonic distortion f = 50 MHz –86 dBc
f = 100 MHz –60
f = 10 MHz –83
3rd-order harmonic distortion f = 50 MHz –61 dBc
f = 100 MHz –49
f
C
= 70 MHz –78
2nd-order intermodulation distortion
V
O
= 1 V
PP
f
C
= 140 MHz –55
200-kHz tone spacing, dBc
f
C
= 70 MHz –82
R
L
= 100 Ω
3rd-order intermodulation distortion
f
C
= 140 MHz –65
f
C
= 70 MHz 70.2
2nd-order output intercept point C
f
C
= 140 MHz 47
200-kHz tone spacing
dBm
R
L
= 100 Ω
f
C
= 70 MHz 32.7
3rd-order output intercept point
f
C
= 140 MHz 24.7
f
C
= 70 MHz 3
1-dB compression point dBm
f
C
= 140 MHz 2
Noise figure 50-Ω system, 10 MHz, G = 6 dB 19.8 dB
Input voltage noise f > 10 MHz 3.3 nV/√Hz
Input current noise f > 10 MHz 1.7 pA/√Hz
DC PERFORMANCE
Open-loop voltage gain (A
OL
) 68 dB
Input offset voltage T
A
= +25°C 1 mV
Average offset voltage drift T
A
= –40°C to +85°C 2.6 μV/°C
Input bias current T
A
= +25°C 6 μA
Average bias current drift T
A
= –40°C to +85°C 20 nA/°C
Input offset current T
A
= +25°C 1.6 μA
Average offset current drift T
A
= –40°C to +85°C 4 nA/°C
INPUT
Common-mode input range high 0.4
V
Common-mode input range low –0.4
Common-mode rejection ratio 90 dB
Differential input impedance 1.3 || 1.8
MΩ || pF
Common-mode input impedance 1.0 || 2.3
(1) Test levels: (A) 100% tested at +25°C. Over-temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: THS4513