Datasheet

THS4511
SLOS471E –SEPTEMBER 2005–REVISED NOVEMBER 2009 www.ti.com
Table 5. THS4511RGT EVM Bill of Materials
SMD REFERENCE PCB MANUFACTURER
ITEM DESCRIPTION SIZE DESIGNATOR QTY PART NUMBER
(1)
1 CAP, 10.0 µF, Ceramic, X5R, 6.3V 0805 C3, C5 2 (AVX) 08056D106KAT2A
2 CAP, 0.1 µF, Ceramic, X5R, 10V 0402 C11-C14 4 (AVX) 0402ZD104KAT2A
3 CAP, 0.22 µF, Ceramic, X5R, 6.3V 0402 C15 1 (AVX) 04026D224KAT2A
4 OPEN 0402 C1, C2, C7-C10 6
5 OPEN 0402 R9, R10 2
6 Resistor, 49.9 Ω, 1/16W, 1% 0402 R12 1 (KOA) RK73H1ETTP49R9F
7 Resistor, 56.2 Ω, 1/16W, 1% 0402 R1, R2 (KOA) RK73H1ETTP56R2F
8 Resistor, 69.8 Ω, 1/16W, 1% 0402 R11 3 (KOA) RK73H1ETTP69R8F
9 Resistor, 86.6 Ω, 1/16W, 1% 0402 R7, R8 2 (KOA) RK73H1ETTP86R6F
10 Resistor, 340 Ω, 1/16W, 1% 0402 R3, R4 2 (KOA) RK73H1ETTP3400F
11 Resistor, 348 Ω, 1/16W, 1% 0402 R5, R6 2 (KOA) RK73H1ETTP3480F
12 Resistor, 0 Ω, 5% 0805 C4, C6 2 (KOA) RK73Z2ATTD
13 Transformer, RF T1 1 (MINI-CIRCUITS) ADT1-1WT
Jack, banana receptance, 0.25" diameter 2
14 J5, J6 (HH SMITH) 101
hole
15 OPEN J1, J7, J8 3
16 Connector, edge, SMA PCB Jack J2, J3 2 (JOHNSON) 142-0701-801
17 Test point, Red TP1, TP2, TP3 3 (KEYSTONE) 5000
18 IC, THS4511 U1 1 (TI) THS4511RGT
19 Standoff, 4-40 HEX, 0.625" length 4 (KEYSTONE) 1808
20 SCREW, PHILLIPS, 4-40, 0.250" 4 SHR-0440-016-SN
21 Printed circuit board 1 (TI) EDGE# 6475513
(1) The manufacturer's part numbers were used for test purposes only.
EVM WARNINGS AND RESTRICTIONS
It is important to operate this EVM within the input and output voltage ranges as specified in the table provided
below.
INPUT RANGE, V
S+
TO V
S–
3.0 V TO 6.0 V
Input Range, V
I
3.0 V to 6.0 V NOT TO EXCEED V
S+
or V
S–
Output Range, V
O
3.0 V to 6.0 V NOT TO EXCEED V
S+
or V
S–
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If
there are questions concerning the input range, please contact a TI field representative prior to connecting the
input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible
permanent damage to the EVM. Please consult the product data sheet or EVM user's guide (if user's guide is
available) prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +30°C. The EVM is
designed to operate properly with certain components above +50°C as long as the input and output ranges are
maintained. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors. These types of devices can be identified using the EVM schematic
located in the material provided. When placing measurement probes near these devices during operation, please
be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
26 Submit Documentation Feedback Copyright © 2005–2009, Texas Instruments Incorporated
Product Folder Link(s): THS4511