Datasheet

THS4502
THS4503
www.ti.com SLOS352E –APRIL 2002–REVISED OCTOBER 2011
ELECTRICAL CHARACTERISTICS V
S
= ±5 V (continued)
R
f
= R
g
= 499Ω , R
L
= 800 Ω, G = +1, Single-ended input unless otherwise noted.
THS4502 AND THS4503
TYP OVER TEMPERATURE
(1)
MIN/
PARAMETER TEST CONDITIONS
TYP/
0°C to -40°C to
25°C 25°C UNITS
MAX
70°C 85°C
OUTPUT COMMON-MODE VOLTAGE CONTROL
Small-signal bandwidth R
L
= 400Ω 180 MHz Typ
Slew rate 2 V
PP
step 87 V/µs Typ
Minimum gain 1 0.98 0.98 0.98 V/V Min
Maximum gain 1 1.02 1.02 1.02 V/V Max
Common-mode offset voltage +2 -1.6/+6.8 -3.6/+8.8 -4.6/+9.8 mV Max
Input bias current V
OCM
= 2.5 V 100 150 170 170 µA Max
Input voltage range ±4 ±3.7 ±3.4 ±3.4 V Min
Input impedance 25 || 1 kΩ || pF Typ
Maximum default voltage V
OCM
left floating 0 0.05 0.10 0.10 V Max
Minimum default voltage V
OCM
left floating 0 -0.05 -0.10 -0.10 V Min
POWER SUPPLY
Specified operating voltage ±5 ±8.25 ±8.25 ±8.25 V Max
Maximum quiescent current 23 28 32 34 mA Max
Minimum quiescent current 23 18 14 12 mA Min
Power supply rejection (±PSRR) 80 76 73 70 dB Min
POWER DOWN (THS4502 ONLY)
Enable voltage threshold Device enabled ON above -2.9 V -2.9 V Min
Disable voltage threshold Device disabled OFF below -4.3 V -4.3 V Max
Power-down quiescent current 800 1000 1200 1200 µA Max
Input bias current 200 240 260 260 µA Max
Input impedance 50 || 1 kΩ || pF Typ
Turnon time delay 1000 ns Typ
Turnoff time delay 800 ns Typ
ELECTRICAL CHARACTERISTICS V
S
= 5 V
R
f
= R
g
= 499 Ω, R
L
= 800 Ω, G = +1, Single-ended input unless otherwise noted.
THS4502 AND THS4503
TYP OVER TEMPERATURE
(1)
MIN/T
PARAMETER TEST CONDITIONS
YP/M
0°C to -40°C to
25°C 25°C UNITS
AX
70°C 85°C
AC PERFORMANCE
G = +1, P
IN
= -20 dBm, R
f
= 392 Ω 320 MHz Typ
G = +2, P
IN
= -30 dBm, R
f
= 1 kΩ 160 MHz Typ
Small-signal bandwidth
G = +5, P
IN
= -30 dBm, R
f
= 1.3 kΩ 60 MHz Typ
G = +10, P
IN
= -30 dBm, R
f
= 1.3 kΩ 30 MHz Typ
Gain-bandwidth product G > +10 300 MHz Typ
Bandwidth for 0.1 dB flatness P
IN
= -20 dBm 180 MHz Typ
Large-signal bandwidth V
P
= 1 V 200 MHz Typ
Slew rate 2 V
PP
Step 1300 V/µs Typ
Rise time 2 V
PP
Step 0.6 ns Typ
Fall time 2 V
PP
Step 0.8 ns Typ
Settling time to 0.01% V
O
= 2 V Step 13.1 ns Typ
(1) See Maximum Die Temperature to Prevent Oscillation section in the Application Information of this data sheet.
Copyright © 2002–2011, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Link(s): THS4502 THS4503