Datasheet

www.ti.com
ABSOLUTE MAXIMUM RATINGS
(1)
DISSIPATION RATINGS
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS
THS4021
THS4022
SLOS265C – SEPTEMBER 1999 – REVISED JULY 2007
over operating free-air temperature range (unless otherwise noted)
VALUE UNIT
V
CC
Supply voltage ± 16.5 V
V
I
Input voltage ± V
CC
V
I
O
Output current 150 mA
V
IO
Differential input voltage ± 4 V
Continuous total power dissipation See Dissipation Ratings table
T
J
Maximum junction temperature 150 ° C
Operating free-air temperature: C-suffix 0 to 70
T
A
° C
I-suffix – 40 to 85
T
stg
Storage temperature – 65 to 150 ° C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 300 ° C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
θ
JA
θ
JC
T
A
= 25 ° C
PACKAGE
( ° C/W) ( ° C/W) POWER RATING
D
(1)
167 38.3 740 mW
DGN
(2)
58.4 4.7 2.14 W
(1) This data was taken using the JEDEC standard low-K test PCB. For the JEDEC proposed high-K test PCB, the θ
JA
is 95 ° C/W with a
power rating at T
A
= 25 ° C of 1.32 W.
(2) This data was taken using 2-oz. (0.071-mm thick) trace and copper pad on a 3-in. × 3-in. (7.62-cm × 7.62-cm) PCB, with the device
soldered directly to the board. For further information, see the Application Information section of this data sheet.
MIN NOM MAX UNIT
Dual supply ± 4.5 ± 16
V
CC+
and V
CC –
Supply voltage V
Single supply 9 32
C-suffix 0 70
T
A
Operating free-air temperature ° C
I-suffix – 40 85
at T
A
= 25 ° C, V
CC
= ± 15 V, R
L
= 150 Ω (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Dynamic Performance
V
CC
= ± 15 V 350
Gain = 10
V
CC
= ± 5 V 280
Small-signal bandwidth
( – 3 dB)
V
CC
= ± 15 V 80
Gain = 20
V
CC
= ± 5 V 70
BW MHz
V
CC
= ± 15 V 17
Bandwidth for 0 1-dB flatness Gain = 10
V
CC
= ± 5 V 17
V
O(pp)
= 20 V, V
CC
= ± 15 V 3.7
Full power bandwidth
(1)
V
O(pp)
= 5 V, V
CC
= ± 5 V 11.8
V
CC
= ± 15 V, 10-V step 470
SR Slew rate
(2)
Gain = 10 V/ μ s
V
CC
= ± 5 V, 5-V step 370
(1) Full-power bandwidth = slew rate / 2 π V
O(Peak)
.
(2) Slew rate is measured from an output level range of 25% to 75%.
Copyright © 1999 – 2007, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): THS4021 THS4022