Datasheet
Table Of Contents
- FEATURES
- APPLICATIONS
- DESCRIPTION
- DEVICE INFORMATION
- ABSOLUTE MAXIMUM RATINGS
- THERMAL INFORMATION
- RECOMMENDED OPERATING CONDITIONS
- PWM OPERATION AT RECOMMENDED OPERATING CONDITIONS
- PLL INPUT PARAMETERS AND EXTERNAL FILTER COMPONENTS
- ELECTRICAL CHARACTERISTICS
- DC Characteristics
- AC Characteristics (BTL)
- SERIAL AUDIO PORTS SLAVE MODE
- I2C SERIAL CONTROL PORT OPERATION
- RESET TIMING (RESET)
- TYPICAL CHARACTERISTICS, BTL CONFIGURATION
- TYPICAL CHARACTERISTICS, SE CONFIGURATION
- TYPICAL CHARACTERISTICS, PBTL CONFIGURATION
- DETAILED DESCRIPTION
- POWER SUPPLY
- ERROR REPORTING
- DEVICE PROTECTION SYSTEM
- SSTIMER FUNCTIONALITY
- CLOCK, AUTO DETECTION, AND PLL
- SERIAL DATA INTERFACE
- PWM Section
- SERIAL INTERFACE CONTROL AND TIMING
- I2C SERIAL CONTROL INTERFACE
- Output Mode and MUX Selection
- 2.1-Mode Support
- Single-Filter PBTL-Mode Support
- Dynamic Range Control (DRC)
- BANK SWITCHING
- 26-Bit 3.23 Number Format
- Recommended Use Model
- CLOCK CONTROL REGISTER (0x00)
- DEVICE ID REGISTER (0x01)
- ERROR STATUS REGISTER (0x02)
- SYSTEM CONTROL REGISTER 1 (0x03)
- SERIAL DATA INTERFACE REGISTER (0x04)
- SYSTEM CONTROL REGISTER 2 (0x05)
- SOFT MUTE REGISTER (0x06)
- VOLUME REGISTERS (0x07, 0x08, 0x09, 0x0A)
- VOLUME CONFIGURATION REGISTER (0x0E)
- MODULATION LIMIT REGISTER (0x10)
- INTERCHANNEL DELAY REGISTERS (0x11, 0x12, 0x13, and 0x14)
- PWM SHUTDOWN GROUP REGISTER (0x19)
- START/STOP PERIOD REGISTER (0x1A)
- OSCILLATOR TRIM REGISTER (0x1B)
- BKND_ERR REGISTER (0x1C)
- INPUT MULTIPLEXER REGISTER (0x20)
- CHANNEL 4 SOURCE SELECT REGISTER (0x21)
- PWM OUTPUT MUX REGISTER (0x25)
- DRC CONTROL (0x46)
- BANK SWITCH AND EQ CONTROL (0x50)
- Revision History
23
22
SCLK
32Clks
LRCLK
LeftChannel
24-BitMode
1
20-BitMode
16-BitMode
15
14
MSB LSB
SCLK
32Clks
RightChannel
2-ChannelRight-Justified(SonyFormat)StereoInput
T0034-03
19 18
1
19 18
1
0
0
0
15
14
15
14
23
22 1
15
14
MSB LSB
19 18
1
19 18
1
0
0
0
15
14
15
14
TAS5711
www.ti.com
SLOS600A –DECEMBER 2009–REVISED AUGUST 2010
it is for the right channel. LRCLK is high for the left channel and low for the right channel. A bit clock running at
32, 48, or 64 × f
S
is used to clock in the data. The first bit of data appears on the data 8 bit-clock periods (for
24-bit data) after LRCLK toggles. In RJ mode the LSB of data is always clocked by the last bit clock before
LRCLK transitions. The data is written MSB first and is valid on the rising edge of bit clock. The DAP masks
unused leading data bit positions.
Figure 43. Right Justified 64-f
S
Format
Copyright © 2009–2010, Texas Instruments Incorporated Submit Documentation Feedback 29
Product Folder Link(s): TAS5711