Datasheet
Table Of Contents
- FEATURES
- APPLICATIONS
- DESCRIPTION
- DEVICE INFORMATION
- ABSOLUTE MAXIMUM RATINGS
- THERMAL INFORMATION
- RECOMMENDED OPERATING CONDITIONS
- PWM OPERATION AT RECOMMENDED OPERATING CONDITIONS
- PLL INPUT PARAMETERS AND EXTERNAL FILTER COMPONENTS
- ELECTRICAL CHARACTERISTICS
- DC Characteristics
- AC Characteristics (BTL)
- SERIAL AUDIO PORTS SLAVE MODE
- I2C SERIAL CONTROL PORT OPERATION
- RESET TIMING (RESET)
- TYPICAL CHARACTERISTICS, BTL CONFIGURATION
- TYPICAL CHARACTERISTICS, SE CONFIGURATION
- TYPICAL CHARACTERISTICS, PBTL CONFIGURATION
- DETAILED DESCRIPTION
- POWER SUPPLY
- ERROR REPORTING
- DEVICE PROTECTION SYSTEM
- SSTIMER FUNCTIONALITY
- CLOCK, AUTO DETECTION, AND PLL
- SERIAL DATA INTERFACE
- PWM Section
- SERIAL INTERFACE CONTROL AND TIMING
- I2C SERIAL CONTROL INTERFACE
- Output Mode and MUX Selection
- 2.1-Mode Support
- Single-Filter PBTL-Mode Support
- Dynamic Range Control (DRC)
- BANK SWITCHING
- 26-Bit 3.23 Number Format
- Recommended Use Model
- CLOCK CONTROL REGISTER (0x00)
- DEVICE ID REGISTER (0x01)
- ERROR STATUS REGISTER (0x02)
- SYSTEM CONTROL REGISTER 1 (0x03)
- SERIAL DATA INTERFACE REGISTER (0x04)
- SYSTEM CONTROL REGISTER 2 (0x05)
- SOFT MUTE REGISTER (0x06)
- VOLUME REGISTERS (0x07, 0x08, 0x09, 0x0A)
- VOLUME CONFIGURATION REGISTER (0x0E)
- MODULATION LIMIT REGISTER (0x10)
- INTERCHANNEL DELAY REGISTERS (0x11, 0x12, 0x13, and 0x14)
- PWM SHUTDOWN GROUP REGISTER (0x19)
- START/STOP PERIOD REGISTER (0x1A)
- OSCILLATOR TRIM REGISTER (0x1B)
- BKND_ERR REGISTER (0x1C)
- INPUT MULTIPLEXER REGISTER (0x20)
- CHANNEL 4 SOURCE SELECT REGISTER (0x21)
- PWM OUTPUT MUX REGISTER (0x25)
- DRC CONTROL (0x46)
- BANK SWITCH AND EQ CONTROL (0x50)
- Revision History
Frequency (Hz)
THD+N (%)
TOTAL HARMONIC DISTORTION + NOISE
vs
FREQUENCY
0.001
0.01
0.1
1
10
20 100 1k 10k 20k
P
O
= 0.5W
P
O
= 1W
P
O
= 2.5W
G015
PVDD = 12V
R
L
= 4Ω
T
A
= 25°C
Frequency (Hz)
THD+N (%)
TOTAL HARMONIC DISTORTION + NOISE
vs
FREQUENCY
0.001
0.01
0.1
1
10
20 100 1k 10k 20k
P
O
= 1W
P
O
= 2.5W
P
O
= 5W
G016
PVDD = 18V
R
L
= 4Ω
T
A
= 25°C
Frequency (Hz)
THD+N (%)
TOTAL HARMONIC DISTORTION + NOISE
vs
FREQUENCY
0.001
0.01
0.1
1
10
20 100 1k 10k 20k
P
O
= 1W
P
O
= 2.5W
P
O
= 5W
G017
PVDD = 24V
R
L
= 4Ω
T
A
= 25°C
Output Power (W)
THD+N (%)
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
0.01 0.1 1 10 50
0.001
0.01
0.1
1
10
PVDD = 12V
PVDD = 18V
PVDD = 24V
G018
f = 1kHz
R
L
= 4Ω
T
A
= 25°C
TAS5711
SLOS600A –DECEMBER 2009–REVISED AUGUST 2010
www.ti.com
TYPICAL CHARACTERISTICS, SE CONFIGURATION
Figure 20. Figure 21.
Figure 22. Figure 23.
18 Submit Documentation Feedback Copyright © 2009–2010, Texas Instruments Incorporated
Product Folder Link(s): TAS5711